Samsung SCX-4x26 Series User Manual Download Page 24

Page: 24 / 139

24 _

Getting started

SETTING UP THE NETWORK

You need to set up the network protocols on the machine to use it as your

network printer. You can set up the basic network settings through the

machine's control panel.

Supported operating systems

The following table shows the network environments supported by the

machine:

Configuring network protocol via the machine

You can set up TCP/IP network parameters, follow the steps listed below.

Make sure your machine is connected to the network with an RJ-45

Ethernet cable.

Make sure you have turned on the machine.

Press

Menu

on the control panel, until you see

Network

on the bottom

line of the display.

Press

to access the menu.

Press the left/right arrow until

TCP/IP

displays.

Press

Press the left/right arrow until

Static

displays.

Press

Press the left/right arrow until

IP Address

displays.

10.

Press

Enter a byte between 0 and 255 using the number keypad and press the

left/right arrow to move between bytes.

Repeat this to complete the address from the 1st byte to the 4th byte.

11.

When you have finished, press

Repeat steps 9 and 10 to configure the other TCP/IP parameters:

subnet mask and gateway address.

ITEM

REQUIREMENTS

Network interface

•

Ethernet 10/100 Base-TX

Network operating system

•

Windows 2000/XP/2003/2008/Vista/7/

Server 2008 R2

•

Various Linux OS

•

Mac OS 10.3 ~ 10.6

Network protocols

•

TCP/IP

•

Standard TCP/IP

•

LPR

•

IPP/HTTP

•

Bonjour

•

DHCP

•

BOOTP

If you want to set up DHCP network protocol, go to

http://

developer.apple.com/networking/bonjour/download/

, select the

Bonjour program that is appropriate for your computer operating

system and install the program. This program will allow you to set

network parameters automatically. Follow the instructions in the

installation window. This program does not support Linux.

Contact the network administrator if you are not sure how to configure.

You can also set up the network settings through the network

administration programs.

•

SyncThru™ Web Admin Service

: Web-based printer

management solution for network administrators.

SyncThru™

Web Admin Service

provides you with an efficient way of

managing network devices and lets you remotely monitor and

troubleshoot network machines from any site with corporate

internet access. Download this program from

http://

solution.samsungprinter.com

•

SyncThru™ Web Service

: Web server embedded on your

network print server, which allows you to:

- Configure the network parameters necessary for the machine to

connect to various network environments.

- Customize machine settings.

•

SetIP

: Utility program allowing you to select a network interface

and manually configure the IP addresses for use with the TCP/IP

protocol. See "Using SetIP program" on page 25.

Summary of Contents for SCX-4x26 Series












































































































































Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands

Samsung SCX-4x26 Series, User Manual

Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands