Samsung SCX-4x26 Series User Manual Download Page 28

Page: 28 / 139

28 _

Getting started

Keypad letters and numbers

Correcting numbers or names

If you make a mistake while entering a number or name, press the left

arrow button to delete the last digit or character. Then enter the correct

number or character.

Inserting a pause

With some telephone systems, you must dial an access code (9, for

example) and listen for a second dial tone. In such cases, you must

insert a pause in the telephone number. You can insert a pause while

you are setting up speed buttons or speed dial numbers.
To insert a pause, press

Redial/Pause

at the appropriate place while

entering the telephone number. A - appears on the display at the

corresponding location.

Using the save modes

Toner Save mode

Toner save mode allows your machine to use less toner on each page.

Activating this mode extends the life of the toner cartridge beyond what

one would experience in the normal mode, but it reduces print quality.

Press

Menu

until

System Setup

appears on the bottom line of the

display and press

Press

when

Machine Setup

appears.

Press the left/right arrow until

Toner Save

appears and press

Press the left/right arrow until the time setting you want appears and

press

Press

Stop/Clear

to return to ready mode.

Power Save mode

Power Save mode allows your machine to reduce power consumption

when it is not in actual use. You can turn this mode on and select a

length of time for which the machine waits after a job is printed before it

switches to a reduced power state.

Press

Menu

until

System Setup

appears on the bottom line of the

display and press

Press

when

Machine Setup

appears.

Press the left/right arrow until

Power Save

appears and press

Press the left/right arrow until the time setting you want appears and

press

Press

Stop/Clear

to return to ready mode.

Setting print job timeout

You can set the amount of time a single print job is active before it must

print.The machine handles incoming data as a single job if it comes in within

the specified time. When an error occurs while processing data from the

computer and the data flow stops, the machine waits the specified time and

then cancels printing if data flow does not resume.

Press

Menu

until

System Setup

appears on the bottom line of the

display and press

Press

when

Machine Setup

appears.

Press the left/right arrow until

Job Timeout

appears and press

Press the left/right arrow until the time setting you want appears and

press

Press

Stop/Clear

to return to ready mode.

KEY

ASSIGNED NUMBERS, LETTERS, OR CHARACTERS

@ / . ‘ 1

A B C a b c 2

D E F d e f 3

G H I g h i 4

J K L j k l 5

M N O m n o 6

P Q R S p q r s 7

T U V t u v 8

W X Y Z w x y z 9

& + - , 0

Summary of Contents for SCX-4x26 Series












































































































































Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands

Samsung SCX-4x26 Series, User Manual

Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands