Samsung SCX-4x26 Series User Manual Download Page 44

Page: 44 / 139

44 _

Scanning

Using Address Book entries

To retrieve an email address, use the following ways:

Speed email numbers

When you are prompted to enter a destination address while sending an

email, enter the speed email number at which you stored the address

you want.
•

For a one-digit speed email location, press and hold the

corresponding digit button from the number keypad.

•

For a two- or three-digit speed email location, press the first digit

button(s) and then hold down the last digit button.

You can also search through memory for an entry by pressing

Address

Book

. See page 44.

Group email numbers

To use a group email entry, you need to search for and select it from

memory.
When you are prompted to enter a destination address while sending an

email, press

Address Book

. See page 44

Searching Address Book for an entry

There are two ways to search for an address in memory. You can either

scan from A to Z sequentially or search by entering the first letters of the

name associated with the address.

Searching sequentially through memory

If necessary, press

Scan/Email

Press

Address Book

until

Search & Send

appears on the bottom

line of the display and press

Press the left/right arrow until the number category you want

appears and press

Press

when

All

appears.

Press the left/right arrow until the name and address you want

appears. You can search upwards or downwards through the entire

memory in alphabetical order.

Searching with a particular first letter

If necessary, press

Scan/Email

Press

Address Book

until

Search & Send

appears on the bottom

line of the display and press

Press the left/right arrow until the number category you want

appears and press

Press the left/right arrow until

appears and press

Enter the first few letters of the name you want and press

Press the left/right arrow until the name you want appears and press

Printing Address Book

You can check your

Address Book

settings by printing a list.

Press

Menu

until

System Setup

appears on the bottom line of the

display and press

Press the left/right arrow until

Report

appears and press

Press the left/right arrow until

Address Book

appears and press

Press the left/right arrow until

E-mail

appears and press

Press

when

Yes

appears to confirm printing.

A list showing your speed button settings, and the speed/group email

entries print out.

Summary of Contents for SCX-4x26 Series












































































































































Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands

Samsung SCX-4x26 Series, User Manual

Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands