Samsung SCX-4x26 Series User Manual Download Page 66

Page: 66 / 139

66 _

Troubleshooting

In the manual tray

When you print using the manual tray and the machine detects that there is

either no paper or that the paper has been improperly loaded, follow the

next steps to release the jammed paper.

Check if the paper is stuck in the feeding area, and if so, pull it out gently

and slowly.

Load a paper into the

manual

tray.

Open the front cover and close it. The machine will resume printing.

In the toner cartridge area

If paper is jammed in the toner cartridge area, follow the next steps to

release the jammed paper.

Open the front cover and pull the toner cartridge out

Remove the jammed paper by gently pulling it straight out as shown

below.

Replace the toner cartridge and close the front cover. Printing

automatically resumes.

In the paper exit area

If paper is jammed in the paper exit area, follow the next steps to release

the jammed paper.

If a long portion of the paper is visible, pull it straight out. Open and close

the front cover firmly. The machine will resume printing.

If you cannot find the jammed paper, or if there is any resistance

removing the paper, stop pulling and go to step 2.

Open the rear cover.

Pull the guide rear on each side down and

carefully take the jammed

paper out of the machine.

Return the guide rear to its original position.

Close the rear cover. Printing automatically resumes.

In the duplex unit area

If the duplex unit is not inserted correctly, paper jam may occur. Make sure

that the duplex unit is inserted correctly.

Pull the duplex unit out of the machine.

If the front cover is not completely closed, the machine will not

operate.

Guide rear

duplex unit

Summary of Contents for SCX-4x26 Series












































































































































Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands

Samsung SCX-4x26 Series, User Manual

Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands