Samsung SCX-4x26 Series User Manual Download Page 38

Page: 38 / 139

38 _

Copying

CHANGING THE DEFAULT COPY SETTINGS

The copy options, including darkness, original type, copy size, and number

of copies, can be set to those most frequently used. When you copy a

document, the default settings are used unless they have been changed by

using the corresponding buttons on the control panel.

Press

Copy

Press

Menu

until

Copy Setup

appears on the bottom line of the display

and press

Press

when

Change Default

appears.

Press the left/right arrow until the setup option you want appears and

press

Press the left/right arrow until the setting you want appears and press

Repeat steps 4 through 5, as needed.

Press

Stop/Clear

to return to ready mode.

ID CARD COPYING

Your machine can print 2-sided originals on one sheet of A4-, Letter-, Legal-

, Folio-, Oficio-, Executive-, B5-, A5-, or A6-sized paper.
When you copy using this feature, the machine prints one side of the

original on the upper half of the paper and the other side on the lower half

without reducing the size of the original. This feature is helpful for copying a

small-sized item, such as a name card.

This copy feature is available only when you place originals on the scanner

glass. Unload the paper in ADF.

Press

ID Copy

Place the front side of an original facing down on the scanner glass

where arrows indicate as shown, and close the scanner lid.

3. Place Front Side and Press[Start]

appears on the display.

Press

Start

Your machine begins scanning the front side and shows

Place Back

Side and Press[Start]

Turn the original over and place it on the scanner glass, where arrows

indicate as shown. Then, close the scanner lid.

Press

Start

to begin copying.

USING SPECIAL COPY FEATURES

You can use the following copy features:

Collation

You can set the machine to sort the copy job. For example, if you make 2

copies of a 3 page original, one complete 3 page document will print

followed by a second complete document.

Press

Copy

Load originals face up into the ADF, or place a single

original face down on the scanner glass.
For details about loading an original, see page 30.

Enter the number of copies using the number keypad.

Press

Menu

until

Copy Setup

appears on the bottom

line of the display and press

Press

when

Change Default

appears.

Press the left/right arrow until

Copy Collation

appears and press

Press the left/right arrow to select

Press

Start

to begin copying.

One complete document will print followed by the second complete

document.

While you are setting copy options, pressing

Stop/Clear

cancels the

changed settings and restores the defaults.

If you press

Stop/Clear

or if no buttons are pressed for

approximately 30 seconds, the machine cancels the copy job and

returns to ready mode.

If the original is larger than the printable area, some portions may not

be printed.

If you press

Stop/Clear

or if no buttons are pressed for approximately

30 seconds, the machine cancels the copy job and returns to ready

mode.

Summary of Contents for SCX-4x26 Series












































































































































Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands

Samsung SCX-4x26 Series, User Manual

Search results

Summary of Contents for SCX-4x26 Series

Reviews:

Related manuals for SCX-4x26 Series

Brands by name

Popular brands