Samsung NX-1232 Technical Manual Download

Page: 141 / 172

This MMC provides display of the current software version of the KSU and the KEYSET,
and the date the product was made. This is a READ ONLY MMC.

PROCEDURE

LCD DISPLAY

1. Press [TRANSFER] and dial 91

2. Press [VOLUME (-) or (+)] to select a display

3. Press [TRANSFER] to and exit.

DEFAULT DATA

RELATED MMC

NONE

This MMC displays the sixteen(16) port attributes:
IDLE, BUSY, CALLBACK, DOOR RING, TRK RING, STN RING, GRP RING, RCL RING, PROGRAM,
ON T HOLD, ON S HOLD, ON E HOLD, IS PAGED, IS SEIZED, WRAP UP, OFF HOOK.

PROCEDURE

LCD DISPLAY

1. Press [TRANSFER] and dial 92

2. Press [VOLUME (-) or (+)] and to see the port status.

3. To clear the port status, press [HOLD]

4. Press [TRANSFER] to save and exit.

DEFAULT DATA

IDLE

RELATED MMC

NONE

NX-SERIES

HYBRID KEY SYSTEM

PROGRAMMING SECTION

MMC 91

SYSTEM VERSION

MMC 92

PORT STATUS

4Programming 1999.9.15 12:44 PM 페이지72

Summary of Contents for NX-1232













































































































































































Search results

Summary of Contents for NX-1232

Reviews:

Related manuals for NX-1232

Brands by name

Popular brands

Samsung NX-1232, Technical Manual

Search results

Summary of Contents for NX-1232

Reviews:

Related manuals for NX-1232

Brands by name

Popular brands