Samsung NX-1232 Technical Manual Download Page 138

Page: 138 / 172

This MMC allows the system administrator to select information to be printed on the SMDR report.

OPTIONS

DESCRIPTIONS

PAGE HEADER

This option determines whether a page header will print at the top
of each page. Normally turned off if SMDR is sent to a call
accounting machine.

LINE PER PAGE

This option selects the length of each page to determine where to print the
SMDR header. The number of lines may be in the range 10 through 99.

INCOMING CALL

This option determines whether or not incoming calls will print on SMDR.

AUTHORIZE CODE

This option determines whether or not the table of authorization

codes will print on SMDR.

LESS START TIME

This option determines whether or not valid calls will include the
minimum call time in total call duration.

ALARM

This option determines whether or not stations receiving an alarm

reminder call will print on SMDR.

COMPANY NAME

This option allows the system administator to enter a 16 character
name which will appear in the SMDR header.

PROCEDURE

LCD DISPLAY

1. Press [TRANSFER] and dial 81

2. Press [VOLUME (-) or (+)] to select the parameter

3. Press [MUTE] or [MESSAGE] to select data

Using KEYPAD, dial

0 for NO
1 for YES

In case of LINE PER PAGE, enter the line number (17~99)

4. In case of COMPANY NAME, refer to MMC 14

(STATION NAME)

5. Press [TRANSFER] to save and exit

DEFAULT DATA

PAGE HEADER

: YES

LINE PER PAGE

: 66

INCOMING CALL

: NO

AUTHORIZE CODE : YES

LESS START TIME : NO

ALARM

: NO

COMPANY NAME

: NONE

RELATED MMC

MMC 80 IO PARAMETER

NX-SERIES

HYBRID KEY SYSTEM

PROGRAMMING SECTION

MMC 81

SMDR OPTIONS

4Programming 1999.9.15 12:44 PM 페이지69

Summary of Contents for NX-1232













































































































































































Search results

Summary of Contents for NX-1232

Reviews:

Related manuals for NX-1232

Brands by name

Popular brands

Samsung NX-1232, Technical Manual

Search results

Summary of Contents for NX-1232

Reviews:

Related manuals for NX-1232

Brands by name

Popular brands