Samsung NX-1232 Technical Manual Download | Manualshive

Page: 50 / 172

background image

EXECUTIVE BARGE-IN (Override)

The feature allows specially-programmed stations to override the automatic
privacy of another station. Programming provides three options: No Barge-in,
With Tone, and Without Tone. When programmed without tone, the barging-in
keyset has its microphone muted. Each station can also be programmed as
secure or not secure. Secure stations cannot be barged-in on. A non-secure
station talking to a secure station cannot be barged-in on. Each station may also
be programmed to enable or disable barge-in.

➥

MMC 24 ASSIGN BARGE-IN

EXTERNAL MUSIC INTERFACE

The system provides internal music on hold (MOH) in the form of a chime. There is
also an input for an external audio source. An RCA style phono jack is provided on
the Base board for a customer-provided source for music on hold and background
music to keysets. Source selection is made via a Base board jumper.

EXTERNAL PAGE INTERFACE

A 600 ohm voice pair is provided for connection to a customer-provided paging system.

FLASH KEY OPERATION

While on an outside line, pressing the FLASH key will flash the central office or
PBX. This is used to activate custom calling features on C.O. lines or in
conjunction with Centrex/PBX operation. System programming allows
adjustment of flash times for C.O. and PBX lines.

➥

MMC 53 TRUNK WIDE TIMERS

⇒

NEW CALL: 600 msec
FLASH PBX: 600 msec

FLEXIBLE NUMBERING

System programming allows each station a programmable two- or three-digit
station number. Re-assignment of these numbers will affect the trunk numbers
and other feature IDs.

➥

MMC 70 DIAL NUMBERING PLAN

FLEXIBLE RINGING

Incoming outside calls can be assigned to ring a station or a station group. The
system provides separate ringing locations for all trunks in both the DAY and the
NIGHT modes.

➥

MMC 43 ASSIGN TRUNK RING

HOT/WARM LINE

Stations can be programmed to call a pre-defined station, station group, outside

NX-SERIES

HYBRID KEY SYSTEM

FEATURES SECTION

3 - 7

3feature 1999.9.15 12:44 PM 페이지11

«
...
48
49
50
51
52
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Brand: Landa Pages: 101

Brand: Taylor-Dunn Pages: 244

Brand: Rayco Pages: 88

Brand: Yamaha Pages: 52

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 106

Brand: Yamaha Pages: 115

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands