manualshive.com logo in svg

Samsung NX-1232, Technical Manual

Share
Download
Samsung NX-1232 Technical Manual Download Page 47

CALL HUNT

If this feature is enabled on a station, an intercom call while busy will be
transferred to another station in the same station group.

➥

MMC 22  CUSTOMER ON/OFF   

⇒

HUNT: ON 

CALL METERING/PRS

You may charge for making outside calls by this feature, which is enabled by
installing an MPD or PRS card on the Base board. This feature is not available on
NX-308. The MPD card detects metering pulses provided by Central Exchange and
determines the call cost by the number of metering pulses and pre-programmed
unit cost. The number of metering pulses is displayed in the keyset LCD. The
number of metering pulses and the unit cost are printed in the ACCOUNT column of
the SMDR. In this case, the ACCOUNT code is not printed in the SMDR. The PRS
card detects the Polarity Reverse Signal when the call is established and/or
terminated. Users who install the PRS card in the system may acquire the exact call
processing time and print this data in SMDR printout. 

➥

MMC 57  CALL COST

CALL PICKUP

With directed call pickup, users can answer calls ringing or held at any station by
dialing a code plus that station's extension number. In addition, calls can be
picked up from a station group in a similar manner. The group pickup feature
allows users to answer any call ringing within a pickup group. Using the 

✱

button, users can answer a call ringing within the user's pickup group.    

➥

MMC 34  ASSIGN PICKUP GROUP

MMC 70  DIAL NUMBERING PLAN   

⇒

DPC: 10 (Direct Pickup ID)

GPC: 66 (Group Pickup ID)
UPC: 67 (UNA Pickup ID)

CALL WAITING / CAMP-ON

Busy stations are notified that a call is waiting (camped-on) when they receive a
tone. This  tone is repeated at a programmable interval. Keysets receive an off-
hook ring signal through the speaker, and single-line stations receive a tone in
the handset. The volume of the camp-on tone can be set by station user.

➥

MMC 50 SYSTEM TIMERS 

⇒

OFF R INT: 15 sec

CENTREX / PBX USE

Centrex and PBX lines can be installed instead of central office (C.O.) trunks.
Feature codes and the hook flash command can be stored at any programmable
button. Toll restriction programming ignores PBX or Centrex access codes so
that toll calls can be controlled when using these services.

➥

MMC 62  PBX ACCESS CODE

NX-SERIES

HYBRID KEY SYSTEM

FEATURES SECTION

3 - 4

3feature  1999.9.15 12:44 PM  페이지8

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands