Samsung NX-1232 Technical Manual Download Page 45 | Manualshive

Page: 45 / 172

background image

ACCOUNT CODE (Voluntary)

Station users may enter an account code of up to seven (7) digits before hanging
up a call. This account code will appear in the last column of the SMDR for that
call record. Keyset users may enter this code using the ACC button without
interrupting a conversation. Single-line set users must temporarily interrupt the
call by hook-flashing and dialing the feature access code. If an MPD or PRS
board is installed, the Call Metering feature is activated and UNIT and COST will
print in the ACCOUNT column of the SMDR.

➥

MMC 57 CALL COST

➥

MMC 70 DIAL NUMBERING PLAN

⇒

ACC: 47

➥

MMC 71 SYSTEM KEY PROGRAMMING

➥

MMC 72 STATION KEY PROGRAMMING

ALL CALL VOICE PAGE

Users can page all keysets and the external paging zone at the same time.
Keysets may be restricted from receiving pages via system programming.

➥

MMC 22 CUSTOMER ON/OFF

ATTENTION TONE

To attract attention, a brief tone precedes all page announcements or intercom
voice calls.

AUTHORIZATION CODES (Voluntary)

Authorization codes are used to validate a station user and give permission to make a
call. These voluntary four-digit codes automatically adjust the dialing station's class of
dialing service to the level assigned to the code. Certain phone numbers (such as
emergency numbers) may be dialed even if the authorization codes are not known.
Authorization table numbers are optionally printed on the SMDR.

➥

MMC 63 AUTHORIZATION CODE

➥

MMC 81 SMDR OPTION

AUTOMATIC HOLD

Station users can enable or disable automatic hold at their keysets. If this feature
is enabled, while engaged in an outside call, pressing another trunk key,
TRANSFER, CONFERENCE, PAGE or DSS, puts the current call on hold. This
is not a user-selectable option.

➥

MMC 12 STATION ON/OFF

⇒

AUTO HOLD: OFF

BACKGROUND MUSIC

Keyset users may choose to hear music through their speakers by pressing the
HOLD button while On-Hook. Either of two sources may be jumper-selected on
the system base board.

➥

MMC 22 CUSTOMER ON/OFF

⇒

BGM: ON

NX-SERIES

HYBRID KEY SYSTEM

FEATURES SECTION

3 - 2

3feature 1999.9.15 12:44 PM 페이지6

«
...
43
44
45
46
47
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Can-Am Maverick Sport X mr 1000R

Brand: BRP Pages: 192

DEFENDER MAX Series 2021

Brand: Can-Am Pages: 211

Brand: KMW Pages: 98

Brand: YSI Pages: 118

2015 RZR XP 1000 EPS

Brand: Polaris Pages: 150

Brand: U-Line Pages: 9

Brand: BAIC Pages: 254

Brand: Jayco Pages: 102

Brand: Yamaha Pages: 32

Brand: KEEWAY Pages: 110

Brand: Cushman Pages: 186

Brand: Yamaha Pages: 158

Brand: Yamaha Pages: 134

POWERSPORTS FR5DGK

Brand: MotoTec Pages: 32

Brand: ShoreLand'r Pages: 10

Brand: Shop fox Pages: 2

Brand: Weber Pages: 11

Brand: Toro Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands