Samsung NX-1232 Technical Manual Download | Manualshive

Page: 60 / 172

background image

AUTOMATIC PRIVACY

All conversations on outside lines and intercom calls are automatically private.
The privacy feature can be turned off on a per-line basis.

BACKGROUND MUSIC

While the keyset is on-hook, the HOLD button alternately turns background
music (BGM) on or off.

➥

MMC 22 CUSTOMER ON/OFF

⇒

BGM: ON

BUSY STATION CALLBACK

When reaching a busy station, callers may request a callback by pressing one
button or dialing a code (44). The system rings the caller back when that station
becomes idle.

BUSY STATION INDICATION (BLF)

DSS/BLF keys may be assigned to any keyset or add-on module. These buttons
will be off when the station is idle, glow red when that station is in use, and flash
when that station is in DND mode.

DIRECT STATION SELECTION (DSS)

Soft keys can be programmed with extension numbers. Users may press these
keys to quickly make or transfer calls to the assigned stations.

DO NOT DISTURB (Programmable)

The Do Not Disturb (DND) feature is used to stop all calls to a station. System
programming can allow or deny use of the DND feature for each station. Parties
calling a station in DND will receive a distinct DND tone.

➥

MMC 12 CUSTOMER ON/OFF

⇒

DND: ON

DOOR LOCK RELEASE

Stations programmed to receive calls from a door phone can dial a code to
activate a contact closure to control a customer-provided electronic door lock.

➥

MMC 50 SYSTEM TIMERS

⇒

DOOR RELS: 100 - 2500 MS

EXCLUSIVE HOLD

Pressing the HOLD button twice will hold a call exclusively at that station,
allowing no other station to pick up the call.

➥

MMC 50 SYSTEM TIMERS

⇒

RCAL HOLD: 45 SEC

NX-SERIES

HYBRID KEY SYSTEM

FEATURES SECTION

3 - 17

3feature 1999.9.15 12:45 PM 페이지21

«
...
58
59
60
61
62
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

PAVER SPECIAL RPS Series

Brand: Etnyre Pages: 61

Brand: Strongway Pages: 3

Brand: TGB Pages: 269

Brand: TGB Pages: 306

Brand: Polaris Pages: 476

855 FINISHOLL Series

Brand: Landoll Pages: 10

Brand: Panasonic Pages: 392

Brand: Camoplast Pages: 55

DewEze 400 Series

Brand: Harper Pages: 75

Brand: Great Dane Pages: 31

Brand: YX Motors Pages: 159

Can-Am Defender DPS HD10

Brand: BRP Pages: 244

BOMBARDIER DS250 2006

Brand: BRP Pages: 284

Brand: Metal-Fach Pages: 60

Brand: Ultraflex Pages: 22

2008 Rev series

Brand: Ski-Doo Pages: 243

Brand: Yamaha Pages: 41

Brand: Westbrook Trailers Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands