manualshive.com logo in svg

Samsung NX-1232, Technical Manual

Share
Download
Samsung NX-1232 Technical Manual Download Page 109

Used to assign SLT ports to be used for data transmission.

VOICE

- The station will be used for voice communication.  All intrusion and 

warning tones will be heard during conversation.

DATA

- The station will be used for data communication.  No intrusion or warning 

tones will occur during data transmission.

PROCEDURE

LCD DISPLAY

1. Press [TRANSFER] and dial 39

2. Display shows.(e.g. 209 is SLT port)

3. Using  [VOLUME (-) or (+)], select the SLT port number.

To select all SLT ports, press 

[VOLUME (-)]

first

4. Press [MUTE] or [MESSAGE] to select VOICE or DATA

The port is set to DATA line.

OR

Dial 

1 for VOICE 

or 2 for DATA

5. Press [TRANSFER] to save and exit

DEFAULT DATA

VOICE line    

RELATED MMC

NONE

NX-SERIES

HYBRID KEY SYSTEM

PROGRAMMING SECTION

MMC 39 

DATA LINE 

4Programming  1999.9.15 12:43 PM  페이지40

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands