Samsung NX-1232 Technical Manual Download

Page: 157 / 172

●

Start to record through handset or speaker phone.

●

After recording, you can hear automatically the recorded message.

NOTE

●

In case of first Power on, record phrase 1 to phrase 4 in sequence.

3.3 Monitoring

●

Dial '18' and the customer passcode Display: 'RECORD:PLAY ?'.

●

Select phrase number (5~8) to play back; Display: 'PLAYING'.

●

You will hear the selected message.

NOTE

●

In order to change a recorded message, record a new message following

precedure (1), so the message will be updated.

●

If you perform the monitoring procedure (2) when no message is recorded,

you may hear an error tone.

●

You cannot record a message while a message is being played back.

●

If you stop during recording, you can neither record a new message, nor

monitor a recorded message, until the predetermined record time elapses.

●

The above description specifies '18' to be dialed for recording. This number

may have been changed by data setting. Confirm the number with the installer.

NX-SERIES

HYBRID KEY SYSTEM

APPENDIX C

DISA VOICE ANOUNCEMENT

5 - 10

5APPENDIX 1999.9.15 12:41 PM 페이지12

Summary of Contents for NX-1232













































































































































































Search results

Summary of Contents for NX-1232

Reviews:

Related manuals for NX-1232

Brands by name

Popular brands

Samsung NX-1232, Technical Manual

Search results

Summary of Contents for NX-1232

Reviews:

Related manuals for NX-1232

Brands by name

Popular brands