manualshive.com logo in svg

Samsung NX-1232, Technical Manual

Share
Download
Samsung NX-1232 Technical Manual Download Page 115

This MMC is used to set the free trunk selection type to a specific trunk, trunk group, or to
several trunk groups.  
There are eleven (11) trunk groups: 9 and 80 through 89, and three types of selecting a
free trunk line in the group.

MODE

DESCRIPTION

DISTRIBUTE

Searches the trunk group in circular order. Each time the group is
accessed, the next available trunk in the group is selected.

High to Low

Searches the trunk group last to first trunk in the group.  If a trunk
is busy, the previous available trunk in the group is selected.

Low to High

Searches the trunk group. If the first trunk in the group is busy, 
the next iavailable trunk in the group is selected.

PROCEDURE

LCD DISPLAY

1. Press [TRANSFER] and dial 45

Display shows the first free trunk selection type

2. Using [MUTE] or [MESSAGE], select the free trunk 

selection mode

OR

Using KEYPAD, dial

1 for DISTRIBUTE
2 for High to Low

or 3 for Low to High.

3. Using [VOLUME (-) or (+)], select the trunk group

4. Press [REDIAL] or [FLASH] to scroll through the group

If dialed number is the member of another trunk group, 
the trunk number will removed from the previous group 
automatically. Dialed number overwrites the previous number.

5. Enter a valid trunk number

6. Press [TRANSFER] to save and exit

DEFAULT DATA  

GROUP 9      

: All trunk lines

GROUP 80~89     

: NONE

RELATED MMC

NONE     

NX-SERIES

HYBRID KEY SYSTEM

PROGRAMMING SECTION

MMC 45 

TRUNK GROUP 

4Programming  1999.9.15 12:43 PM  페이지46

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands