Samsung NX-1232 Technical Manual Download | Manualshive

Page: 38 / 172

background image

FIGURE 7-5 CONNECTING EXTERNAL BATTERY

8. BEFORE POWER UP

During initial installation, it is best to verify proper system operation before plugging in
any amphenol-type cables to the MDF. If you have already plugged the cables in,
unplug them. Verify that the AC voltage at the dedicated electric outlet is correct.

Make sure the AC power switch is in the OFF position and memory back-up switch is
ON. Plug the KSU power cord into the dedicated polarized AC outlet. Turn the AC
power switch to the ON position, and verify the status of the "POWER", "MONITOR",
and "IDLE" LEDs on the cover of the KSU. A steady "POWER" LED indicates the
presence of power, and a blinking "MONITOR" LED indicates that the main
processor is functioning. A steady "IDLE" LED indicates that no one is using the
system. If the "POWER" LED fails to illuminate, unplug the system, remove the power
supply, and check the AC fuse located on the bottom.

If the fuse is good but the "POWER" LED does not illuminate, you must correct the
problem before continuing., Turn off the power switch., Unplug all expansion cards
except Base board. Turn the system on. Check the "POWER" LED again. If the
problem is corrected, you have a defective card. Test and remove the faulty card
before continuing.

If the LED still does not light, unplug the KSU and change power supplies or Base
board. This in all probability will solve the problem. If it does not, contact Samsung
Technical Support.

NX-SERIES

HYBRID KEY SYSTEM

INSTALLATION SECTION

2 - 32

2INSTALL 1999.9.15 12:45 PM 페이지36

«
...
36
37
38
39
40
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Brand: BERG Pages: 12

Brand: Odes Industry Pages: 73

Brand: Polaris Pages: 142

Brand: TrailMaster Pages: 13

Raider Max 175D

Brand: Dazon Pages: 43

Brand: Daymak Pages: 33

Off-Roader 36EL

Brand: Texas Pages: 27

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 83

PRO HAULER YXP1000

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 194

Brand: Yamaha Pages: 287

Brand: CanyCom Pages: 43

Brand: CanyCom Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands