Samsung NX-1232 Technical Manual Download Page 119 | Manualshive

Page: 119 / 172

background image

This MMC is used to customize the tone cadence on a system-wide basis to any one of
the eight available selections.
Call Technical Support before changing any cadences, as some systems may require
default settings.

PROCEDURE

LCD DISPLAY

1. Press [TRANSFER] and dial 51

Display shows

2. Press [VOLUME (-) or (+)] to select a tone

3. Press [MUTE] or [MESSAGE] to set dial tone to

continuous or interrupted tone

Interrupt tone default data is: 1000 0250 1000 0250 ms

4. Dial new interrupt value for interrupt time,

(ON/OFF/ON/OFF) in 50 ms steps.
Each field is 3 digits (UNIT: 10 ms)
(e.g. 100/030/100/030 = 1000 ms [100

×

10]

'ON' and 300 ms [030

×

10] 'OFF' time)

5. Press [TRANSFER] to save and exit

DEFAULT DATA

TONE NAME

DISPLAY

DATA

DIAL TONE

(DT)

CONTINUOUS TONE

RING BACK TONE

(RBT)

1000 2000 1000 2000 ms

BUSY TONE

(BST)

0500 0500 0500 0500 ms

TRSF TONE

(TT)

0200 0200 0200 0200 ms

ERROR TONE

(ERT)

0500 0250 0500 0250 ms

CO LINE RING

(COR)

1000 3000 1000 3000 ms

STATION RING

(STR)

0400 0200 0400 3000 ms

RELATED MMC

NONE

NX-SERIES

HYBRID KEY SYSTEM

PROGRAMMING SECTION

MMC 51

TONE/RING CADENCE

4Programming 1999.9.15 12:43 PM 페이지50

«
...
117
118
119
120
121
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Brand: KAYO MOTOR Pages: 90

Brand: Eton America Pages: 96

Brand: Aosom Pages: 36

Brand: Topcon Pages: 58

Double Eagle - Electric

Brand: J&J Amusements Pages: 275

Brand: Erde Pages: 8

Brand: Tomberlin Pages: 151

Brand: Baja Pages: 82

Brand: PARKIT360 Pages: 7

Raider Pro 250 S

Brand: Dazon Pages: 31

Brand: PARKIT360 Pages: 13

Brand: Erde Pages: 6

Brand: ShoreLand'r Pages: 2

Brand: ShoreLand'r Pages: 10

Brand: Ski-Doo Pages: 34

Legend SE 800 SDI 2003

Brand: Ski-Doo Pages: 40

Grand Touring SE 1997

Brand: Ski-Doo Pages: 46

Brand: Ski-Doo Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands