Samsung NX-1232 Technical Manual Download | Manualshive

Page: 152 / 172

background image

APPENDIX B

DATABASE DOWNLOAD

1. Introduction To Database Download Programming

A database download programming capability has been incorporated into the N X -
S E R I E S via the communication (serial) SMDR port of the optional S M D R / R - M M C
card mounted in the base unit.
This is a software utility designed to allow a certified NX-SERIES technician the ability
to perform a database download on-site.

1.1 Customer Site Requirements

Certain conditions must be satisfied before installing the software package on a
personal computer:

1) Install the optional NX-SMDR/R-MMC card in the base unit.
2) Use a 286 or higher IBM-PC or 100% IBM-compatible computer with the following

●

MS-DOS version 5.0 or higher

●

MS-WINDOWS version 3.1 or higher

●

3

¼

" or 5

½

" high-density floppy drive

●

VGA monitor.

3. Rs-232C cable

2. Installing Database Downloading

2.1 Getting Started

1) Create a directory to store the DATABASE DOWNLOAD program.

2) Copy the file to the new directory. The file is compressed and will have a

name similar to N X 7 1 2 2 9 . e x e where 7 1 2 2 9 is the date the file was generated.

3) Type "NX71229" to uncompress the file or Double-click file name on the file

name in the Windows file manager.

4) Double-click on the icon that was created by the install program in the

Windows file manager - "NX_DOWN.EXE".

3. Setup of Database Downloading Program

3.1 Starting NX Download Program

1) Connect the cable required (RS-232C)

2) Turn on the PC.

NX-SERIES

HYBRID KEY SYSTEM

APPENDIX B

DATABASE DOWNLOAD

5 - 5

5APPENDIX 1999.9.15 12:41 PM 페이지7

«
...
150
151
152
153
154
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Brand: Ski-Doo Pages: 162

Brand: AC Air Technology Pages: 46

Brand: cectek Pages: 125

Brand: Madill Pages: 44

Brand: Mi-T-M Pages: 65

Brand: Columbia Pages: 36

Brand: Trail Rover Pages: 38

2006 Sportsman 500 EFI

Brand: Polaris Pages: 126

Brand: KAYO MOTO Pages: 6

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 156

Brand: Suzuki Pages: 50

EcoLight MPG585

Brand: Malone Pages: 9

Magnum 500 2000

Brand: Polaris Pages: 5

Brand: Polaris Pages: 13

600 IQ Widetrak

Brand: Polaris Pages: 140

2008 Scrambler 500 2X4 International

Brand: Polaris Pages: 124

Supersport 2007

Brand: Polaris Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands