Samsung NX-1232 Technical Manual Download | Manualshive

Page: 61 / 172

background image

EXECUTIVE / SECRETARY HOT LINES

A hands-free communication link is established when the EXECUTIVE/SECRETARY
button is pressed. When the EXECUTIVE is in DND mode, all calls are forwarded to
the SECRETARY and only the SECRETARY can call the EXECUTIVE. This feature
is only available between two keysets. Each SECRETARY station may be associated
with two EXECUTIVEs, and an EXECUTIVE station has only one SECRETARY.

➥

MMC 36 ASSIGN BOSS/SECRETARY

FORCED AUTO ANSWER

The called station automatically answers via speakerphone. Callers may request
this feature by pressing one button or dialing a code (14).

➥

MMC 72 STATION KEY PROGRAMMING

GROUP LISTENING

A keyset assigned this feature may turn on the speaker while using the handset.
This allows a group of people to listen to the remote party over the speaker without
turning on the microphone and causing interference to the conversation on the line.

➥

MMC 72 STATION KEY PROGRAMMING

HEADSET OPERATION

Each keyset can be programmed to allow the use of a headset. In Headset mode,
the hookswitch is disabled and the SPEAKER button is used to answer calls.

➥

MMC 12 STATION ON/OFF

⇒

HEADSET: OFF

HEARING AID COMPATIBLE

All NX keysets are hearing aid-compatible, as required by part 68 of the FCC
requirements.

HOT KEYPAD

If Hot Keypad is enabled, it is not necessary to lift the handset or press the
SPEAKER button to begin dialing.

➥

MMC 12 STATION ON/OFF

⇒

HOT KEYPAD

KEY TONE SELECTION

This feature allows users to hear a slight tone when pressing any keypad button
on their keyset.

➥

MMC 12 STATION ON/OFF

⇒

KEY TONE

NX-SERIES

HYBRID KEY SYSTEM

FEATURES SECTION

3 - 18

3feature 1999.9.15 12:45 PM 페이지22

«
...
59
60
61
62
63
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Brand: Cub Cadet Pages: 28

Brand: Yerf-Dog Pages: 59

Brand: Makita Pages: 128

Brand: Yamaha Pages: 46

Brand: Yamaha Pages: 155

Brand: Yamaha Pages: 190

amphibious, off-road utility vehicle

Brand: Centaur Pages: 56

Brand: Erde Pages: 4

UTV 2x4 Series 11

Brand: Polaris Pages: 108

Brand: Landoll Pages: 70

Brand: HAPERT Pages: 45

Brand: Taylor-Dunn Pages: 150

Sasquatch 1000W

Brand: Daymak Pages: 24

Venture Lite PZ50RTB

Brand: Yamaha Pages: 100

Brand: Panasonic Pages: 303

Brand: AMF Pages: 28

Brand: Suzuki Pages: 477

Brand: Yamaha Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands