Samsung NX-1232 Technical Manual Download | Manualshive

Page: 46 / 172

background image

BATTERY BACKUP (Memory Protection)

In the event that power is lost to the system, all customer data contained in memory is
backed up by a base board Ni/Cd battery sufficient for at least seven (7) days
continuous loss of system power. When power is restored, the battery will recharge.

BATTERY BACKUP (System)

If an external 24V battery is connected, the system remains fully operational if
AC power is interrupted. Calls in progress are not interrupted when the system
switches over. When AC power is restored, the system recharges the batteries.
Battery maximum size is limited by charging capacity.

CALL FORWARDING

Allows the user to forward incoming calls under various conditions. Calls can be
redirected to the operator group, an external number, or another station or
group. If the destination is in DND, the caller will receive a DND tone. Calls
cannot be forwarded to a door phone.

➥

MMC 11 CALL FORWARD

➥

MMC 70 DIAL NUMBERING PLAN

➥

MMC 71 SYSTEM KEY PROGRAMMING

➥

MMC 72 STATION KEY PROGRAMMING

Forward All

Not affected by the condition of the station. All calls are immediately
directed to the designated forwarding destination.

Forward Busy

Forwards calls only while the station is busy. The station user can
originate calls as usual.

Forward No Answer

This feature forwards calls not answered within a pre-programmed time. The
station user can originate and receive calls normally. The time is programmable
on a per-station basis to allow for differences in individual work habits.

External Call Forward

A keyset user can forward calls to an external phone number. Each outside line
may be programmed to either follow or ignore station call forwarding.

➥

MMC 16 KEY EXTENDER

CALL HOLD

Both outside and internal calls can be put on hold at any station. Users may dial an
access code or press the HOLD button to retrieve the held call. If you leave the call on
hold longer than the programmed hold recall time, it will re-call your station.

➥

MMC 50 SYSTEM TIMERS

⇒

HOLD RECALL TIME: 045 SEC

NX-SERIES

HYBRID KEY SYSTEM

FEATURES SECTION

3 - 3

3feature 1999.9.15 12:44 PM 페이지7

«
...
44
45
46
47
48
...
»

Summary of Contents for NX-1232













































































































































































Reviews:

No comments

Related manuals for NX-1232

Brand: Yamaha Pages: 176

Brand: Polaris Pages: 146

RYKER 2023 Series

Brand: Can-Am Pages: 222

Brand: SAF-HOLLAND Pages: 20

Vyper 4WD 1100cc 4 seater XY1100UEL

Brand: gio Pages: 261

Brand: Foldy Pages: 44

GMX 125 SPORTZILLA X

Brand: GMX MOTORBIKES Pages: 28

Brand: Can-Am Pages: 140

Brand: CanyCom Pages: 43

Brand: CanyCom Pages: 51

Brand: CanyCom Pages: 64

Brand: CanyCom Pages: 73

Brand: CanyCom Pages: 75

Brand: CanyCom Pages: 81

HAUL-MASTER 92696

Brand: Harbor Freight Tools Pages: 10

Brand: Yamaha Pages: 34

Brand: Baja motorsports Pages: 8

Brand: KAYO MOTO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands