Samsung HHSM-G500005-1 Installation Manual Download Page 80

Page: 80 / 90

www.jouleuk.co.uk | www.joule.ie

Error

Code

Contents

Measure

Product op. in

error condition

Error Type

Outdoor unit /

Comp. / Ind. unit

475

Outdoor fan 2 error

Check th einput power connection status

Check the connection status of the motor and

the outdoor unit PCB

Check the indoor/outdoor unit fuse

Operation off

Self diagnostic

error

554

Gas leak error

Check the coolant charging status

Check the indoor EVA sensor

Check if the outdoor unit service value is open

Check that the indoor/outdoor installation

pipe/wiring are correct

Operation off

Self diagnostic

error

556

Capacities not matched

Check the option code of the indoor unit

Operation off

Outdoor unit

protection control

error

601

Communication error be-

tween the indoor unit and

wired remote controller

Check the connection wire between the indoor

unit and the wired remote controller

Operation off

Wired remote

controller error

602

Communication error

between the Master

and Slave wired remote

controllers

Check the option switch for defining the

master and slave (only one master and one

slave can exist)

Normal opera-

tion

Wired remote

controller error

606

COM1/COM2 cross

installation error

Check that wired remote controller is con-

nected to the COM2 terminal of the indoor unit

Normal opera-

tion

Wired remote

controller error

607

Communication error

between the Master

and Slave wired remote

controllers.

Check the option switch for defining the

master and slave (only one master and one

slave can exist)

Normal opera-

tion

Wired remote

controller error

Fault Codes

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands