Samsung HHSM-G500005-1 Installation Manual Download Page 22

Page: 22 / 90

www.jouleuk.co.uk | www.joule.ie

Installing The Unit

Outdoor Unit Installation

The outdoor unit must be installed on a rigid and stable base to avoid any increase in the noise level

and vibration. Particularly if the outdoor unit is to be installed in a location exposed to strong or at a

height, the unit must be fixed to an appropiate support (wall or ground).

Fix The Outdoor Unit With Anchor

620mm

940mm

330mm

328mm

384mm

Anchor Bolt Hole

The anchor bolt must be 20mm

or higher from the base

• The anchor bolt must be 20mm or higher from the base surface.

• When tightening the anchor bolt, tighten the rubber washer to prevent outdoor

unit bolt connection part from corroding.

• Make a drain outlet around the base for outdoor unit drainage.

• If the outdoor unit is installed on the roof, you have to check the celing

strength and waterproof the unit.

Outdoor Unit Support

• Ensure the wall will be able to suspend the weight of rack and outdoor unit.

• Install the rack close to the column as much as possible.

• Install proper grommet in order to reduce noise and residual vibration transferred by outdoor

unit towards wall.

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands