Samsung HHSM-G500005-1 Installation Manual Download Page 7

Page: 7 / 90

Heat Pump Installation Guide

Heat Pump

Installation Checklist

Please register your product online

MUST BE COMPLETED AND

THEN REGISTERED ONLINE

TO COMPLETE WARRANTY

Has all air been removed from emitters?

Have all emitters been balanced correctly?

If UFH is installed, have correct flowrates been set?

If UFH is installed, are all valves on manifolds/pumps fully open?

Radiator/UFH Plumbing

Is the correct size breaker used for heatpump?

Is an isolation switch installed for the heat pump and mounted on a fixed structure out beside

heatpump?
Is the correct size power supply cable used for heat pump?

Are all cable protrusions avoiding condensate tray?

Is the correct communication cable installed and wired into correct terminals?

Heat Pump Wiring

Is the correct size breaker used for controller on cylinder?

Is an isolation switch installed for controller and mounted on a fixed structure beside Controller?

Is the correct size power supply cable used for controller on cylinder?

Is the correct communication cable installed and wired into correct terminals?

Is the flowswitch wired back into correct terminal on control panel? (Smart Plumb Compact not

applicable)

Cylinder Wiring

Is each zone/floor corresponding with the correct zone valve?

Are all heating controls powered from controller on cylinder?

Are all heating controls wired and working?

Heating Controls/Stats Wiring

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands