Samsung HHSM-G500005-1 Installation Manual Download Page 25

Page: 25 / 90

Heat Pump Installation Guide

Drain Plug x 1ea

Drain Cap x 3ea

30mm

Drain Hole Ø 20 x 4ea

1. Prepare a water drainage channel around the foundation, to drain waste water from around the unit.

2. If the water drainage of the unit is not easy, please build up the unit on a foundation of concrete

blocks, etc. (the height of the foundation should be a maximum of 150mm).

3. If you install the unit on a frame, please install a water-proof plate within 150mm of the under-

side of the unit in order to prevent the invasion of water from the lower direction.

4. When installing the unit in a place frequently exposed to snow, pay special attention to elevate

the foundation as high as possible.

5. If you unstall the unit on a building frame, please install a waterproof plate (field supply) within

150mm of the underside of the unit in order to avoid the drain water dripping.

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands