Samsung HHSM-G500005-1 Installation Manual Download Page 18

Page: 18 / 90

www.jouleuk.co.uk | www.joule.ie

First Fix Notes

Outdoor Unit

Cable

Size

Breaker Size

HHSM-G500005-1

4.0mm

16Amp

HHSM-G500009-1

4.0mm

20Amp

HHSM-G500012-1

6.0mm

25Amp

HHSM-G500016-1

6.0mm

32 Amp

Primary Pipework From Outdoor Unit To Indoor Cylinder

• 5W – 28mm copper

• 9kW – 28mm copper

• 12kW – 28mm copper

• 16kW – 32mm copper

• Outdoor pipework should be fully insulated and protected from water and moisture.

• If outdoor pipework is required use Joule outdoor low energy loss pipework (supplied by the meter)

Electrical Supply And Cable Requirements

• Shielded 0.75mm 2 core cable from outdoor unit to cylinder / wiring centre location.

• Shielded 0.75mm 2 core cable from wiring centre to samsung controller.

• Power supply to outdoor unit to be terminated with IP67 isolator located next to the unit.

• Power supply to indoor unit (MIM board) to be terminated switch fused isolator.

Outdoor Unit

Cable

Size

Breaker Size

MIM E03BN (5kW)

4.0mm

20Amp

MIM E03AN

4.0mm

20Amp

• Power supply to the MIM units must connect

to the RCD fitted inside of the MIM unit.

Cable

Size

No. of

Cores

Location

0.75mm

2 Core

Screened

From indoor unit to outdoor

unit.

F1 & F2 Comms.

0.75mm

2 Core +

Earth

From Zone 1 stat or

Underfloor heating control

cen- tre to Indoor unit.

0.75mm

2 Core +

Earth

From Zone 2 stat or

Underfloor heating control

cen- tre to indoor unit.

0.75mm

2 Core

Screened

From MIM unit to remote

controller.

• When installing the outdoor unit take great

care to install as per the detailed notes for

installation locations. The Air-to-Water Heat

Pump must have minimum clearance of

300mm at the rear of the unit and 1500mm

at the front of the unit.

• The Air-to-Water Heat Pump must not be in-

stalled in a location without these clearances

available.

• Condensation will form on the Air-to-Water

Heat Pump. Ensure adequate provisions

are put in place to prevent water forming on

the ground beneath the Air-to-Water Heat

Pump, resulting in a potential Health and

Safety hazard.

• The Air-to-Water Heat Pump must be in-

stalled vertically and should not be tilted at

an angle.

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands