Samsung HHSM-G500005-1 Installation Manual Download Page 78

Page: 78 / 90

www.jouleuk.co.uk | www.joule.ie

Fault Codes

Error

Code

Contents

Measure

Product op. in

error condition

Error Type

Outdoor unit /

Comp. / Ind. unit

101

Indoor unit communica-

tion error

Check the communication cable of indoor

unit. Check the DC output voltage at the com-

munication terminal.

Operation off

Communication

error

102

Indoor unit/outdoor unit

communication time-out

error: errors in more than

6 packets

Check the outdoor communication cable

connection. Check DC output voltag and the

communication terminal.

Operation off

Communication

error

121

Indoor temperature sen-

sor (open/short error)

Check indoor unit room temperaute sensor.

Check indoor unit PCB connector CN41

(White)

Operation off

Indoor sensor error

122

Indoor unit Eva in sensor

(Open/Short)

Check indoor unit pipe sensor. Check indoor

PCB connector CN41 (White)

Operation off

Indoor sensor error

128

Indoor unit Eva in sensor

disconnection

Check the disconnection of indoor unit pipe

sensor.

Operation off

Indoor sensor error

153

Indoor floating switch

secondary detection

Check indoor unit float sensor. Check indoor

PCB connector CN5 (black)

Operation off

Self diagnostic

error

202

Indoor/outdoor commu-

nication error (1 min)

Check the communication connection

between indoor and outdoor units. Check the

power line and communication cable connec-

tion status.

Operation off

Communication

error

203

Communication error

between indoor/outdoor

INVIMAIN <-> MICOM

(1 min)

Check MAIN MICOM

Check INVERTER MICOM

Operation off

Communication

error

221

Outdoor temperature

sensor error

Check sensor connection status

Check sensor location

Check sensor resistance

Operation off

Outdoor sensor

error

237

COND temperature sen-

sor error

Check sensor connection status

Check sensor location

Check sensor resistance

Operation off

Outdoor sensor

error

251

[Inverter] Emission tem-

perature sensor error

Check sensor connection status

Check sensor location

Check sensor resistance

Operation off

Outdoor sensor

error

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands