Samsung HHSM-G500005-1 Installation Manual Download Page 11

Page: 11 / 90

Heat Pump Installation Guide

Warranty

Registration Procedure

A Samsung accredited installer to..

Warranty Procedure

WARRANTY

REGISTRATION PROCEDURE

WARRANTY PROCEDURE

Complete installation

& Commissioning

End user calls a/c

engineer/Samsung

Samsung

Internal approval

a/c engineer

calls distributor

Samsung entitlement /

document checks

Warranty work

completed

Prepare info

and documents

Make claim

on GSPN

Samsung internal

checks

Claim paid

Provide Commissioning &

Maintenance documents

a/c engineer

verifies fault

With help from distributor,

Request registration

with Samsung

a/c contacted

& sent to site

End user Customer is

welcomed & contacted

Distributor contacts
Samsung & logs call

Service order sent to

Service Partner

(inc labour contribution)

Complete

warranty work

A samsung accredited installer to...

Performing Warranty Work

Registration with Samsung must occur within 28 days of Commissioning date.

Warranty Reimbursement (by distributor/service partner)

Contact 03307262677 or [email protected] for Commissioning and maintenance documentation as required.

Work should only be carried out following the issue of a Service Order (SO) number.

Any Parts required should be ordered on GSPN by a distributor using the SO and a distributor will prepare

the claim for Labour and parts following repair. Once paid the distributor pays the installer the labour allowance.

WARRANTY

REGISTRATION PROCEDURE

WARRANTY PROCEDURE

Complete installation

& Commissioning

End user calls a/c

engineer/Samsung

Samsung

Internal approval

a/c engineer

calls distributor

Samsung entitlement /

document checks

Warranty work

completed

Prepare info

and documents

Make claim

on GSPN

Samsung internal

checks

Claim paid

Provide Commissioning &

Maintenance documents

a/c engineer

verifies fault

With help from distributor,

Request registration

with Samsung

a/c contacted

& sent to site

End user Customer is

welcomed & contacted

Distributor contacts
Samsung & logs call

Service order sent to

Service Partner

(inc labour contribution)

Complete

warranty work

A samsung accredited installer to...

Performing Warranty Work

Registration with Samsung must occur within 28 days of Commissioning date.

Warranty Reimbursement (by distributor/service partner)

Contact 03307262677 and Commissioning and maintenance documentation as required.

Work should only be carried out following the issue of a Service Order (SO) number.

Any Parts required should be ordered on GSPN by a distributor using the SO and a distributor will prepare

the claim for Labour and parts following repair. Once paid the distributor pays the installer the labour allowance.

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands