Samsung HHSM-G500005-1 Installation Manual Download Page 81

Page: 81 / 90

Heat Pump Installation Guide

Troubleshooting

Error

Code

Meaning

Troubleshooting

E177

Emergency stop

Indoor unit ($POUSPM kit) orders emergency stop.

Check the indoor unit ($POUSPM kit)

E201

Control kit quantity is mismatched.

Control kit quantity must be matched with outdoor unit 1 by 1.

Check the $POUSPM kit quantity. It must be 1EA.

E403

Detection of outdoor freezing when compressor

stops.

Outdoor unit (condenser) froze.

Check condenser.

E404

Protection of outdoor overload when compressor

stops.

Compressor is overloaded. Please check same as E461 and

check compressor when it starts.

E416

Discharge temperature of a compressor in an

outdoor unit is overheated.

Discharge temperature is overheated.

E440

Heating operation is not available since the out-

door air temperature is over 35 degrees.

Check the outdoor temperature.

E441

Cooling operation is not available since the out-

door air temperature is lower than -15 degrees.

Check the outdoor temperature.

E465

Compressor overload error

Compressor is overloaded. Please check same as E461 and

check compessor when it starts.

E468

Current sensor error

Exchange INVERTER PBA.

E471

Outdoor EEPROM error

EEPROM date is wrong. Exchange EEPROM or MAIN PBA. (This

error doesn’t occur in EMF 150-AM)

E474

IPM (IGBT Module) or PFCM temperature sensor

error

Exchange INVERTER PBA.

E484

PFC overload error

Check reactor located in control plate.

If reactor is normal, exchange INVERTER PEA.

E500

IPM is over heated

Check INVERTER PBA’s temperature. Power off and cool down

INVERTER PBA, and then restart the outdoor unit.

E556

Capacity mismatching between indoor and

outdoor

EEPROM data is wrong.

Exchange EEPROM or MAIN PBA

E557

Option code miss matching among the indoors

(only for DPM)

EEPROM data is wrong.

(This error doesn’t occur in EMF 150-AM)

E911

Emergency stop

Ensure flow switch is fitted onto pipework and connected to

Samsung PCB.

Ensure flow rate is above 16 litres per minute.

Ensure all air is removed from system.

Check circulation pumps speed setting.

Check zone valves are not sticking cloesd.

Check direction of flow switch on pipework.

Check direction of pump on pipework.

Check direction of Flow Meter on pipework.

E912

Emergency stop

Check circulation pumps are not operating.

check flow switch is installed on horizontal pipework.

Ensure 150mm of horizontal pipework each side of flow switch.

Summary of Contents for HHSM-G500005-1



























































































Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands

Samsung HHSM-G500005-1, Installation Manual

Search results

Summary of Contents for HHSM-G500005-1

Reviews:

Related manuals for HHSM-G500005-1

Brands by name

Popular brands