manualshive.com logo in svg

Rohde & Schwarz CMW-B400B, User Manual

Share
Download
Rohde & Schwarz CMW-B400B User Manual Download Page 95

List of Commands

R&S

®

CMW-B400B/-B405A

95

User Manual 1176.8116.02 ─ 04

READ:AUDio:MEAS<i>:ANALog:MULTitone:MAXimum?...............................................................................77
READ:AUDio:MEAS<i>:ANALog:MULTitone:SDEViation?.............................................................................77
READ:AUDio:MEAS<i>:ANALog:SINGletone:AVERage?...............................................................................71
READ:AUDio:MEAS<i>:ANALog:SINGletone:CURRent?...............................................................................71
READ:AUDio:MEAS<i>:ANALog:SINGletone:EXTReme?..............................................................................71
READ:AUDio:MEAS<i>:ANALog:SINGletone:SDEViation?............................................................................71
READ:AUDio:MEAS<i>:ANALog:SPECtrum:CURRent?.................................................................................73
READ:AUDio:MEAS<i>:DIGital:FFTNoise:AVERage?....................................................................................81
READ:AUDio:MEAS<i>:DIGital:FFTNoise:CURRent?.................................................................................... 81
READ:AUDio:MEAS<i>:DIGital:FFTNoise:FREQuency?................................................................................81
READ:AUDio:MEAS<i>:DIGital:FFTNoise:MAXimum?...................................................................................81
READ:AUDio:MEAS<i>:DIGital:MULTitone:AVERage?..................................................................................77
READ:AUDio:MEAS<i>:DIGital:MULTitone:CURRent?.................................................................................. 77
READ:AUDio:MEAS<i>:DIGital:MULTitone:MAXimum?................................................................................. 77
READ:AUDio:MEAS<i>:DIGital:MULTitone:SDEViation?............................................................................... 77
READ:AUDio:MEAS<i>:DIGital:SINGletone:AVERage?.................................................................................72
READ:AUDio:MEAS<i>:DIGital:SINGletone:CURRent?................................................................................. 72
READ:AUDio:MEAS<i>:DIGital:SINGletone:EXTReme?................................................................................ 73
READ:AUDio:MEAS<i>:DIGital:SINGletone:SDEViation?.............................................................................. 73
READ:AUDio:MEAS<i>:DIGital:SPECtrum:CURRent?...................................................................................74
ROUTe:AUDio<i>:SCENario:AMGenerator.....................................................................................................56
ROUTe:AUDio<i>:SCENario:CATalog:MASTer?............................................................................................ 57
ROUTe:AUDio<i>:SCENario:EASPeech.........................................................................................................56
ROUTe:AUDio<i>:SCENario:EDSPeech.........................................................................................................57
ROUTe:AUDio<i>:SCENario:MSTest..............................................................................................................57
ROUTe:AUDio<i>:SCENario?......................................................................................................................... 57
SENSe:AUDio:SPEech<i>:ELOGging:ALL?....................................................................................................90
SENSe:AUDio:SPEech<i>:ELOGging:LAST?.................................................................................................91
SOURce:AUDio:GEN<i>:ANALog:ACOupling.................................................................................................83
SOURce:AUDio:GEN<i>:ANALog:FFTNoise:LEVel........................................................................................90
SOURce:AUDio:GEN<i>:ANALog:MULTitone:CRESt.....................................................................................85
SOURce:AUDio:GEN<i>:ANALog:MULTitone:LSELection............................................................................. 85
SOURce:AUDio:GEN<i>:ANALog:MULTitone:STARt.....................................................................................89
SOURce:AUDio:GEN<i>:ANALog:MULTitone:STOP......................................................................................89
SOURce:AUDio:GEN<i>:ANALog:MULTitone:TDEFinition.............................................................................88
SOURce:AUDio:GEN<i>:ANALog:MULTitone:TLEVel....................................................................................85
SOURce:AUDio:GEN<i>:ANALog:MULTitone:TONE<no>:TDEFinition..........................................................86
SOURce:AUDio:GEN<i>:ANALog:SINGletone:FREQuency...........................................................................83
SOURce:AUDio:GEN<i>:ANALog:SINGletone:LEVel.....................................................................................84
SOURce:AUDio:GEN<i>:ANALog:STATe.......................................................................................................82
SOURce:AUDio:GEN<i>:ANALog:STYPe.......................................................................................................83
SOURce:AUDio:GEN<i>:DIGital:ACOupling................................................................................................... 83
SOURce:AUDio:GEN<i>:DIGital:FFTNoise:LEVel.......................................................................................... 90
SOURce:AUDio:GEN<i>:DIGital:MULTitone:CRESt.......................................................................................85
SOURce:AUDio:GEN<i>:DIGital:MULTitone:LSELection................................................................................85
SOURce:AUDio:GEN<i>:DIGital:MULTitone:STARt....................................................................................... 89
SOURce:AUDio:GEN<i>:DIGital:MULTitone:STOP........................................................................................ 89
SOURce:AUDio:GEN<i>:DIGital:MULTitone:TDEFinition............................................................................... 88
SOURce:AUDio:GEN<i>:DIGital:MULTitone:TLEVel...................................................................................... 86
SOURce:AUDio:GEN<i>:DIGital:MULTitone:TONE<no>:TDEFinition............................................................87

深圳德标仪器 

135-1095-0799

Summary of Contents for CMW-B400B


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands