manualshive.com logo in svg

Rohde & Schwarz CMW-B400B, User Manual

Share
Download
Rohde & Schwarz CMW-B400B User Manual Download Page 77

Command Reference

R&S

®

CMW-B400B/-B405A

77

User Manual 1176.8116.02 ─ 04

FETCh:AUDio:MEAS<i>:ANALog:MULTitone:CURRent?
FETCh:AUDio:MEAS<i>:ANALog:MULTitone:AVERage?
FETCh:AUDio:MEAS<i>:ANALog:MULTitone:MAXimum?
FETCh:AUDio:MEAS<i>:ANALog:MULTitone:SDEViation?
READ:AUDio:MEAS<i>:ANALog:MULTitone:CURRent?
READ:AUDio:MEAS<i>:ANALog:MULTitone:AVERage?
READ:AUDio:MEAS<i>:ANALog:MULTitone:MAXimum?
READ:AUDio:MEAS<i>:ANALog:MULTitone:SDEViation?

Returns the current, average, maximum and standard deviation results of an analog
multitone measurement.

The measured levels are either returned as relative dB values or as absolute dBV val-
ues, depending on the configured result mode, see 

CONFigure:AUDio:MEAS<i>:

ANALog:MULTitone:RMODe

 

on page 75.

If the signal comprises less than 20 tones, NAV is returned for each "missing" tone.

The ranges indicated below apply to all results except standard deviation results. The
minimum for standard deviation results equals 0. The maximum equals the width of the
indicated range divided by two. Exceptions are explicitly stated.

Return values: 

<Reliability>

Reliability Indicator

<Level_0> ...
<Level_19>

Audio levels measured at the frequencies of the test tones
Range: 

-150 dB to 150 dB or -150 dBV to 36 dBV

Default unit: dB or dBV

Example: 

See 

Multitone Measurement

Usage: 

Query only

Firmware/Software: 

V3.2.10

FETCh:AUDio:MEAS<i>:DIGital:MULTitone:CURRent?
FETCh:AUDio:MEAS<i>:DIGital:MULTitone:AVERage?
FETCh:AUDio:MEAS<i>:DIGital:MULTitone:MAXimum?
FETCh:AUDio:MEAS<i>:DIGital:MULTitone:SDEViation?
READ:AUDio:MEAS<i>:DIGital:MULTitone:CURRent?
READ:AUDio:MEAS<i>:DIGital:MULTitone:AVERage?
READ:AUDio:MEAS<i>:DIGital:MULTitone:MAXimum?
READ:AUDio:MEAS<i>:DIGital:MULTitone:SDEViation?

Returns the current, average, maximum and standard deviation results of a digital mul-
titone measurement.

The measured levels are either returned as relative dB values or as absolute dBFS val-
ues, depending on the configured result mode, see 

CONFigure:AUDio:MEAS<i>:

DIGital:MULTitone:RMODe

 

on page 75.

If the signal comprises less than 20 tones, NAV is returned for each "missing" tone.

Audio Measurements

深圳德标仪器 

135-1095-0799

Summary of Contents for CMW-B400B


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands