Rohde & Schwarz CMW-B400B User Manual Download

Page: 73 / 97

Command Reference

R&S

CMW-B400B/-B405A

User Manual 1176.8116.02 ─ 04

READ:AUDio:MEAS<i>:DIGital:SINGletone:EXTReme?
READ:AUDio:MEAS<i>:DIGital:SINGletone:SDEViation?

Returns the current, average, extreme and standard deviation results of a digital single
tone measurement.

The ranges indicated below apply to all results except standard deviation results. The
minimum for standard deviation results equals 0. The maximum equals the width of the
indicated range divided by two. Exceptions are explicitly stated.

Return values:

<1_Reliability>

Reliability Indicator

<2_THDPercent>

THD result as percentage
Range:

0 % to 100 %

Default unit: %

<3_THDdB>

THD result as dB value
Range:

-150 dB to 0 dB

Default unit: dB

<4_THDPlusN>

THD + N result
Range:

0 % to 100 %

Default unit: %

<5_SINAD>

Range:

0 dB to 150 dB

Default unit: dB

<6_SNR>

Range:

0 dB to 150 dB

Default unit: dB

<7_WeightLevRMS> Weighted level RMS result

Range:

0 FS to 1 FS

Default unit: FS

<8_BandLevRMS>

Bandpass level RMS result
Range:

0 FS to 1 FS

Default unit: FS

Example:

See

Single Tone Measurement

Usage:

Query only

Firmware/Software:

V3.2.10

FETCh:AUDio:MEAS<i>:ANALog:SPECtrum:CURRent?
READ:AUDio:MEAS<i>:ANALog:SPECtrum:CURRent?

Returns the current spectrum trace of an analog single tone measurement.

Return values:

Reliability Indicator

Audio Measurements

深圳德标仪器

135-1095-0799

Summary of Contents for CMW-B400B


































































































Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands

Rohde & Schwarz CMW-B400B, User Manual

Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands