Rohde & Schwarz CMW-B400B User Manual Download | Manualshive

Page: 71 / 97

background image

Command Reference

R&S

®

CMW-B400B/-B405A

71

User Manual 1176.8116.02 ─ 04

Parameters:

<DiagramMode>

OFF | ON

OFF

: Do not evaluate the results and hide the diagram

ON

: Evaluate the results and show the diagram

*RST:

OFF

Example:

See

Single Tone Measurement

Firmware/Software:

V3.2.20

Manual operation:

See

"Spectrum > Off / On"

6.3.4 Single Tone Measurement Results

The following commands return the results of single tone measurements.

FETCh:AUDio:MEAS<i>:ANALog:SINGletone:CURRent?

.................................................... 71

FETCh:AUDio:MEAS<i>:ANALog:SINGletone:AVERage?

....................................................71

FETCh:AUDio:MEAS<i>:ANALog:SINGletone:EXTReme?

...................................................71

FETCh:AUDio:MEAS<i>:ANALog:SINGletone:SDEViation?

................................................. 71

READ:AUDio:MEAS<i>:ANALog:SINGletone:CURRent?

..................................................... 71

READ:AUDio:MEAS<i>:ANALog:SINGletone:AVERage?

.....................................................71

READ:AUDio:MEAS<i>:ANALog:SINGletone:EXTReme?

.................................................... 71

READ:AUDio:MEAS<i>:ANALog:SINGletone:SDEViation?

...................................................71

FETCh:AUDio:MEAS<i>:DIGital:SINGletone:CURRent?

...................................................... 72

FETCh:AUDio:MEAS<i>:DIGital:SINGletone:AVERage?

......................................................72

FETCh:AUDio:MEAS<i>:DIGital:SINGletone:EXTReme?

..................................................... 72

FETCh:AUDio:MEAS<i>:DIGital:SINGletone:SDEViation?

................................................... 72

READ:AUDio:MEAS<i>:DIGital:SINGletone:CURRent?

....................................................... 72

READ:AUDio:MEAS<i>:DIGital:SINGletone:AVERage?

....................................................... 72

READ:AUDio:MEAS<i>:DIGital:SINGletone:EXTReme?

...................................................... 73

READ:AUDio:MEAS<i>:DIGital:SINGletone:SDEViation?

.....................................................73

FETCh:AUDio:MEAS<i>:ANALog:SPECtrum:CURRent?

..................................................... 73

READ:AUDio:MEAS<i>:ANALog:SPECtrum:CURRent?

.......................................................73

FETCh:AUDio:MEAS<i>:DIGital:SPECtrum:CURRent?

........................................................74

READ:AUDio:MEAS<i>:DIGital:SPECtrum:CURRent?

.........................................................74

FETCh:AUDio:MEAS<i>:ANALog:SINGletone:CURRent?
FETCh:AUDio:MEAS<i>:ANALog:SINGletone:AVERage?
FETCh:AUDio:MEAS<i>:ANALog:SINGletone:EXTReme?
FETCh:AUDio:MEAS<i>:ANALog:SINGletone:SDEViation?
READ:AUDio:MEAS<i>:ANALog:SINGletone:CURRent?
READ:AUDio:MEAS<i>:ANALog:SINGletone:AVERage?
READ:AUDio:MEAS<i>:ANALog:SINGletone:EXTReme?
READ:AUDio:MEAS<i>:ANALog:SINGletone:SDEViation?

Returns the current, average, extreme and standard deviation results of an analog sin-
gle tone measurement.

Audio Measurements

深圳德标仪器

«
...
69
70
71
72
73
...
»

Summary of Contents for CMW-B400B


































































































Reviews:

No comments

Related manuals for CMW-B400B

Brand: Panasonic Pages: 72

KW9M Eco-Power Meter

Brand: Panasonic Pages: 2

Brand: DayTronic Pages: 54

Brand: Bacharach Pages: 2

Brand: Bachmann Pages: 33

Brand: i-SENS Pages: 50

Brand: MADDALENA Pages: 4

Brand: Macnaught Pages: 4

ProcessMaster FEP630 series

Brand: ABB Pages: 92

Brand: National Instruments Pages: 15

Brand: Oldham Pages: 96

Brand: Alfa Laval Pages: 18

Brand: Xylem Pages: 10

Brand: Lasertec Pages: 32

Brand: IDEAL Pages: 20

Brand: GTR Pages: 8

AcuRev 1310 Series

Brand: AccuEnergy Pages: 109

AUER Atemluft 300 bar

Brand: MSA Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands