Rohde & Schwarz CMW-B400B User Manual Download | Manualshive

Page: 37 / 97

background image

GUI Reference

R&S

®

CMW-B400B/-B405A

37

User Manual 1176.8116.02 ─ 04

Remote command:

CONFigure:AUDio:MEAS<i>:DIGital:SINGletone:LIMit

Spectrum > Off / On

Enables or disables the measurement of single tone spectrum results and shows or
hides the result diagram.

Remote command:

CONFigure:AUDio:MEAS<i>:ANALog:SPECtrum:DMODe
CONFigure:AUDio:MEAS<i>:DIGital:SPECtrum:DMODe

Spectrum > Display

These settings configure the axes of the spectrum diagram, select which traces shall
be displayed and configure the markers.

These settings can also be accessed via hotkeys. See

chapter 3.4.4, "Modifying Dia-

chapter 3.4.5, "Using Markers"

Remote command:
n/a

4.3.4 Multitone Settings

The "Multitone" measurement displays the individual audio levels at up to 20 different
test tones, corresponding to 20 audio input frequencies. The results can be presented
in a bar graph or in a table.

The number of test tones included in the multitone signal and the frequencies of the
individual test tones are defined via the generator to which the measurement is cou-
pled, see

chapter 4.4.3, "Multitone Settings"

The following settings are specific for multitone measurements. They can be config-
ured separately for analog and digital measurements. The description applies to both.

Fig. 4-8: Multitone measurement settings

Audio Measurement Settings

深圳德标仪器

135-1095-0799

«
...
35
36
37
38
39
...
»

Summary of Contents for CMW-B400B


































































































Reviews:

No comments

Related manuals for CMW-B400B

Brand: UEi Pages: 4

Brand: Parr Instrument Pages: 110

Brand: Yamaha Pages: 8

BML SL1-ALZ-ZZ Series

Brand: Balluff Pages: 26

Brand: Hammond Pages: 130

Brand: Hach Pages: 28

Brand: Olympus Pages: 12

Brand: Keithley Pages: 343

Brand: Keithley Pages: 334

Brand: La Crosse Technology Pages: 2

Brand: Bamo Pages: 17

Brand: Hilti Pages: 146

Brand: Lasertec Pages: 28

Brand: Hanna Instruments Pages: 2

Brand: Zero 88 Pages: 32

PHYSICS line C.A 832

Brand: Chauvin Arnoux Pages: 43

Fusion-L 6 digit

Brand: London Electronics Pages: 44

Brand: Allen Organ Company Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands