RITE-HITE ELIMINATOR II 610 Series, Installation Instructions & Owner'S Manual

Page: 28 / 40

H1
Pub. 28620002 Rev. 4 - JUNE 2014
6 1 0 S E R I E S C 4 - S T Y L E C U R T A I N
Table of Contents
File Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
General Precautions . . . . . . . . . . . . . . . . . . . . . . . . .H1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .H1
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . .H1
C4 Style Curtain (Up to 15'3" Off Grade) . . . . . . .H1
C4 Style Curtain (15'4" Off Grade and Over) . . . .H3
C4 Style Curtain (15'4" Off Grade and Over
Common Member) . . . . . . .H4
File Information
Document Name: 28620002
Date Last Revised: 06/30/2014
Revision: 4
General Precautions
Introduction
The following installation instructions are complete
for all applications of the C4-Style Curtain that are
normally available. Any application of the C4-Style
curtain that is outside of normal application guidelines,
should be referred to Order Engineering for installation
instructions. These instructions also assume that the
installer is outside the building facing the loading dock
position.
Illustrations
Illustrations for this document are contained on drawing
#2862-0003
Installation
C4-Style Curtain (Up to 15 3 Off-Grade)
These instructions illustrate how to install a standard
C4-Style curtain face mounted up to and including 15'-
3" off grade on a stand alone unit and assumes that
the header brackets are installed on side members.
1. Located on the canopy top cover front flap is a
small tab that locates the center of the unit. Marking
this location makes it easier to install curtain face.
(Note: Verification of this location can be done by
measuring across the top of the front of the unit and
dividing this measurement by 2.)
2. Using the velcro on the curtain face and velcro on
the front bar, temporarily hang the curtain face from
the canopy top cover. Make sure curtain face top
edge is aligned with the front bar. There will be
slight variations in the velcro location on the front
bar, so make sure you align the two edges and not
the velcro(s). Also, make sure that the curtain face
is underneath the canopy top cover front flap and
that it is centered on the mark made in the previous
step. The middle stay on the C4 Style curtain face
should align with the mark made in step 1. See
Figure 1) (Go to 5162-0004 for gutter installation
instructions)
3. Attach the curtain face to the front bar using the
supplied tek-screws and washers.
Fasteners
should align with center of stays and be located half
way down the front bar. The screws are intended to
drill through the Velcro, the stay and the front bar at
the same time. There are no pre drilled holes, so
take care in centering the fasteners correctly. Make
sure that the large thin washer is between the front
curtain and the tek-screw head. Install screws in
every stay location, and three to four screws on
each end, past the last stay on each side. The last
screw on the outside is always located 1” off the
curtain face outside edge. (Note: Do not get last
screw to close to outside. Leave 1” of curtain
remaining.) Install the rest of the screws evenly in
space provided. Make sure at least three screws
are installed through the end cap front flap and of
those three screws, at least one catches the last
inch of the endcap towards the middle. In some
situations, all of these screws will land in end cap
front flap.
4. Lay the canopy top cover front flap with velcro over
the newly installed curtain face and screws. Take
care in positioning the flap so it is even along the
front of the unit. This flap keeps the water from
entering behind the front curtain.
WARNING
Post safety warning and
barricade work area, at dock level
and ground level to prevent
unauthorized use of the dock
position while service work is
being performed.