RITE-HITE ELIMINATOR II 610 Series, Installation Instructions & Owner'S Manual

Page: 24 / 40

G1
Pub. 28610002 Rev. 2 - JUNE 2014
6 1 0 S E R I E S C - S T Y L E C U R T A I N
Table of Contents
File Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G1
General Precautions . . . . . . . . . . . . . . . . . . . . . . . . .G1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G1
Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G1
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . .G1
C Style Curtain . . . . . . . . . . . . . . . . . . . . . . . . . . .G1
Windstraps, standard . . . . . . . . . . . . . . . . . . . . . .G2
Windstraps, Common Member . . . . . . . . . . . . . .G2
Pull Rope Cleat . . . . . . . . . . . . . . . . . . . . . . . . . .G2
Operation of Pull Rope . . . . . . . . . . . . . . . . . . . .G3
File Information
Document Name: 28610002
Date Last Revised: 06/30/2014
Revision: 2
General Precautions
Introduction
The following installation instructions are complete
for all applications of the C-style curtain that are
normally available. Any application of the C-style
curtain that is outside of normal application guidelines,
should be referred to Order Engineering for installation
instructions. These instructions also assume that the
installer is outside the building facing the loading dock
position.
Illustrations
Illustrations for this document are contained on drawing
#2861-0003
Installation
C-Style Curtain
These instructions illustrate how to install a standard
C-style curtain face on a stand alone unit and
assumes that the header brackets are installed on side
members.
1. Located on the canopy top cover front flap is a small
tab that locates the center of the unit. Marking this
location makes it easier to install curtain face. (Note:
Verification of this location can be done by
measuring across the top of the front of the unit and
dividing this measurement by 2.)
2. Locate center of c-style curtain face by locating a
small tab at center. Marking this location makes it
easier to install curtain face. Also, there are tabs
that locate other attachment points on curtain face.
Marking these locations will make it easier to install
curtain face.
3. Using the velcro on the curtain face and velcro on
the front bar, temporarily hang the curtain face from
the canopy top cover. Make sure curtain face top
edge is aligned with the front bar. There will be
slight variations in the velcro location on the front
bar, so make sure you align the two edges and not
the velcro(s). Also, make sure that the curtain face
is underneath the canopy top cover front flap and
that it is centered on the mark made in the previous
step. (See Figure 1) (Go to 5162-0004 for gutter
installation instructions)
4. Attach the curtain face to the front bar using the
supplied tek-screws and washers.
Fasteners
should align with tabs marked at specified locations
on curtain face and also half way down the front bar.
The screws are intended to drill through the Velcro,
the stay and the front bar at the same time. There
are no pre drilled holes, so take care in centering
the fasteners correctly. Make sure that the large thin
washer is between the front curtain and the tek-
screw head. Install screws in every stay location,
and three to four screws on each end, past the last
stay on each side. The last screw on the outside is
always located 1” off the curtain face outside edge.
(Note: do not get last screw to close to outside.
Leave 1” of curtain remaining.) Install the rest of the
screws evenly in space provided. Make sure at
least three screws are installed through the end cap
front flap and of those three screws, at least one
catches the last inch of the end cap towards the
middle. In some situations, all of these screws will
land in end cap front flap.front curtain.
WARNING
Post safety warning and
barricade work area, at dock level
and ground level to prevent
unauthorized use of the dock
position while service work is
being performed.