"Drive Thru" Face Curtain Brackets
These instructions illustrate how to install face curtain
brackets that are required for the proper function of the
C4 Style Face Curtain when applied in the "Drive Thru"
application.
Failure to install these brackets could
result in face curtain damage during operation.
There are two methods of attaching brackets to canopy
frame, either before face curtain installation or after.
These instructions are applicable for either way, but
are written specifically for installation of the brackets
before the face curtain installation. Make appropriate
changes if attaching after face curtain installation.
1. Before attaching face curtain to canopy header,
attach the (3) face curtain brackets to canopy front
bar.
2. First, find the center of the canopy front bar where
face curtain is to be attached and mark the location
on the backside of the front bar, underneath the
canopy. This marks the location of the first and
center bracket. (See Figure 11) (Note: this can be
done on the ground for ease of installation)
3. From the center location, make (2) more marks, 34"
away in each direction. These mark the outside
bracket locations. (See Figure 11)
4. Using the provided self drilling/tapping screws,
attach each bracket the backside of the front bar.
The brackets go thru the canopy cover mounting
flap and thru the angle welded on the front bar.
(See Figures 11, 12 & 13)
5. The brackets need to relatively centered on the
stays on the face curtain. They will be mounted
slightly forward and should contact the face curtain
when the face curtain gets attached. (See Figure
13) Make sure the brackets are securely attached
to front bar and screws are seated all the way in.
DO NOT OVER TIGHTEN AND STRIP SCREWS!
6. Attach the face curtain per the standard instructions.
(Note: The brackets can be attached after the face
curtain, except it is a little more difficult.)
Fastening Methods
Concrete Block or Brick Wall
Through bolt fastening is required. Bore a hole
through the building wall. Use a 3/8" diameter
threaded rod with a washer, nut and jam nut on
each end - it may be necessary to install a back-up
plate inside the building wall when the wall will not
support the bolt.
Concrete Tilt-Up Walls (Precast)
Use a 3/8" lag bolt with expansion shields, 3/8" one
piece anchor bolts with expansion collar, or
equivalent fastener. If building wall is too hin to
effectively hold the lag bolt or anchor bolt, the
through bolt method of attachment is required.
* See anchor manufacturer’s recommendation for
minimum anchor embedment to determine
appropriate anchor length.
Metal Side Building
Through bolt method of attachment is required for
this building style. It will be necessary to install a
back-up plate that is fastened directly to structural
members when it is not possible to fasten directly to
structural building members. Use a 3/8" diameter
bolt with a washer and lock nut to fasten the unit to
the structural members of the building or to the
back-up plates. If necessary, use a 3/8" diameter
threaded rod with a washer and lock nut on each
end.
610 SERIES CANOPY STYLE HEADER
INSTALLATION INSTRUCTIONS/FASTENING METHODS
F7
Pub. 16100003 Rev. 6 - SEPTEMBER 2015
Summary of Contents for ELIMINATOR II 610 Series
Page 12: ...610 SERIES SIDE FRAME D5 Pub 56560007 Rev 4 JUNE 2014 FIGURE 5 FIGURE 6 FIGURE 7...
Page 27: ...610 C STYLE CURTAIN OPERATION OF PULL ROPES Pub 28610002 Rev 2 JUNE 2014 G4 FIGURE 5...
Page 38: ...38 Pub ECII 610 Rev 11 September 2015 ELIMINATORTM II COMBOSHELTERTM II 610 SERIES NOTES...
Page 39: ...Pub ECII 610 Rev 11 September 2015 39 ELIMINATORTM II COMBOSHELTERTM II 610 SERIES NOTES...
