610 SERIES CANOPY STYLE HEADER
6. For one side of the common member unit only,
continue with Steps 5-12 of the standard canopy
style header installation procedure. Then return to
step 7 of these instructions.
7. Pull the end cap located on the common member
side frame end, down into position. (See Figure 8)
The endcap is designed to fit around the mounting
bracket and top of side frame. There should be
approximately 1” of material left over. This material
can be used to trim to fit or left loose.
8. Finally, wrap the end cap front flap onto the front bar
of header assembly at the same time attaching it to
the endcap flap velcro located at the top, front face
of the side curtain. (See Figure 6 & 8) Align edge on
end cap to top edge of the front bar itself. Do not
align to velcro. Also, do not pull end cap tightly
around corner. Allow the end cap to wrap corner
loosely. This allows the header to flex and proper
movement of side members relative to header
during normal operation. For common member
units, the endcap front face attaches to side frame
via the velcro on the top, front face of the side
curtain while on standard units it is attached to
velcro on the side.
9. Repeat this procedure for the other corresponding
header assembly used on the common member
side frame. (Note: The canopy covers of the
common member unit may need to be adjusted for
the two tops to fit properly. Adjust by repositioning
polystrip loop in front bar frame assembly. Canopy
cover ends should just touch or have a small space
between them)
10. Attach the endcap seam flap. (See Figure 10) Do
this by centering it between the two vertical velcro
strips sewn on the endcaps front face. Starting at
the bottom, align the seam flap to the bottom of the
endcap and go up. Do not lay seam flap completely
flat, but allow some slack between the velcro seams
for header movement. The seam flap should tuck
under the front bar flaps on canopy covers. The
face curtains will mount under the front bar flaps,
but over top of the endcaps and the seam.
11. The curtain face can either be installed now or after
the last steps in these instructions.
12. Attach the top cover seam flap. (See Figure 10)
This seam flap needs to go from the canopy back
edge at wall, and follow the velcro on the top cover
down and over front bar flap. Do not lay seam flap
completely flat, but allow some slack between the
velcro seams for header up and down movement.
The end of the seam flap should end up even with
the edge of the front bar flap. Adjust and trim at
building wall if necessary.
13. Nail the back of the top cover seam flap at the
building wall. Put (1) nail on each side into the
header backer boards of each canopy. (See Figure
10)
14. Caulk along the entire edge of the canopy top at the
building wall, making sure the ends are covered.
Use a good grade of flexible caulk.
FIGURE 9
Pub. 16100003 Rev. 6 - SEPTEMBER 2015
F6
FIGURE 10
Summary of Contents for ELIMINATOR II 610 Series
Page 12: ...610 SERIES SIDE FRAME D5 Pub 56560007 Rev 4 JUNE 2014 FIGURE 5 FIGURE 6 FIGURE 7...
Page 27: ...610 C STYLE CURTAIN OPERATION OF PULL ROPES Pub 28610002 Rev 2 JUNE 2014 G4 FIGURE 5...
Page 38: ...38 Pub ECII 610 Rev 11 September 2015 ELIMINATORTM II COMBOSHELTERTM II 610 SERIES NOTES...
Page 39: ...Pub ECII 610 Rev 11 September 2015 39 ELIMINATORTM II COMBOSHELTERTM II 610 SERIES NOTES...
