Rich electric Invertek CombiPlus User Manual Download Page 95

Page: 95 / 128

Page 95

E2-07: Charging for ? sec

Main Menu>Programming>ENT>Aux-Relay>ENT

This setting switches the Aux-Relay 1 OFF when the AC CHARGER started for a certain time

(E2-07). This can be useful when the Aux-Relay 1 is for instance used a low battery alarm.

Use the Set Udc Lower than ? Voltage (E1-03) setting to start the alarm and use this setting

(E2-07) to stop it.

※

Note: As along as the battery voltage is lower than the specified limit (E1-03), the alarm will be

active.

E2-08: Fan OFF for ? sec

Main Menu>Programming>ENT>Aux-Relay>ENT

This will switch the Aux-Relay 1 OFF when the internal fan switches off. This can be used

together with the E1-08: Fan ON for ? sec setting to drive an external fan.

E2-09: Charge finished for ? Min (When E2-09=0, ignore this setting)

Main Menu>Programming>ENT>Aux-Relay>ENT

This condition becomes active when the charge bulk phase is finished for a certain time

(E2-09).

For the charge curve, take a look at for instance the Charge Current (D1-08) setting.

This is useful when the Aux-Relay 1 is used to start a generator. Once started, one might want to

keep the generator on until the batteries are more or less charged.

E2-10: Aux-Relay 1 not ON for ? minutes (When E2-10=0, ignore this setting)

Main Menu>Programming>ENT>Aux-Relay>ENT

If one does not need special off condition, one can use this setting and the Aux-Relay 1 will

switch off automatically when there has been no ON condition for a certain time (E2-10).

E2-11: AC IN loss for ? sec (When E2-11=0, ignore this setting)

Main Menu>Programming>ENT>Aux-Relay>ENT

This setting will switch off Aux-Relay1 if the RMS value of AC IN voltage is too low for a

certain time (E2-11).

This AC level is determined by the AC IN Low Disconnect (B2-01) setting.

Use this setting (E2-11) to disable re-starting of a generator which is switched off by hand when

the Aux-Relay 1 is used to generate a start signal for that generator.

Summary of Contents for Invertek CombiPlus




























































































































Search results

Summary of Contents for Invertek CombiPlus

Reviews:

Brands by name

Popular brands

Rich electric Invertek CombiPlus, User Manual

Search results

Summary of Contents for Invertek CombiPlus

Reviews:

Brands by name

Popular brands