Rich electric Invertek CombiPlus User Manual Download Page 64

Page: 64 / 128

Page 64

5.2 Green Power Smart Feature

Green Power Smart Feature

Renewable Energy MODES 3 & 4

Green Power Smart Feature:

Green Power Smart Modes 3 and 4 are designed to conserve energy, whether you are connected

to the mains grid power or for use in a standalone power system where there is no mains

available.

The Green Power Smart feature uses renewable energy such as solar, wind and hydro generation

to recharge the batteries and will only connect to the mains grid or start the generator as a last

resort.

Even if the Combi unit cannot support the load, it will automatically connect to the grid or start

the generator to help supply continuous power until the load has decreased. This ingenious smart

power feature will make sure your batteries always get the charge they require, helping them to

last longer in demanding installations.

Summary of Contents for Invertek CombiPlus




























































































































Search results

Summary of Contents for Invertek CombiPlus

Reviews:

Brands by name

Popular brands

Rich electric Invertek CombiPlus, User Manual

Search results

Summary of Contents for Invertek CombiPlus

Reviews:

Brands by name

Popular brands