Rich electric Invertek CombiPlus User Manual Download Page 3

Page: 3 / 128

Page 3

Table of CONTENTS

Introduction.....................................................................................................................................

Features...................................................................................................................... 7

Layout ........................................................................................................................ 8

About CombiPlus ...................................................................................................... 9

Specifications ........................................................................................................... 10

Dimensions............................................................................................................... 13

Chapter 1 Installation.....................................................................................................................

1.1 Box Contents...................................................................................................... 17

1.2 Location ............................................................................................................. 18

1.3 Requirements..................................................................................................... 19

1.4 Connection of Battery Cables .......................................................................... 19

1.5 Connection of AC Cabling ............................................................................... 20

1.6 AC Cabling Schematic Layout (Multiple Ciruits AC Output) ..................... 22

1.7 AC Cabling Schematic Layout (Single Ciruit AC Output)........................... 23

1.8 Second Battery .................................................................................................. 24

1.9 Voltage Sense ..................................................................................................... 24

1.10 Battery Temperature Sensor (BTS-3)........................................................... 24

1.11 Three Sets of Automatic Relays (RY1,RY2,RY3) Outputs......................... 24

1.12 Parrellel Conection ......................................................................................... 24

1.13 3-Phase Operation........................................................................................... 25

1.14 MEN (Main Earth Neutral) Grounding ....................................................... 25

1.15 Remote Control Panel (RCP-4) ..................................................................... 25

1.16 Ventilation (Standard Single Unit)................................................................ 26

1.17 Ventilation (Optinal Fan Cover Application) "Standard Single Unit" ..... 26

1.18 Ventilation (Multible or 3-Phase Appliaction) ............................................. 27

Summary of Contents for Invertek CombiPlus




























































































































Search results

Summary of Contents for Invertek CombiPlus

Reviews:

Brands by name

Popular brands

Rich electric Invertek CombiPlus, User Manual

Search results

Summary of Contents for Invertek CombiPlus

Reviews:

Brands by name

Popular brands