Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 164

Page: 164 / 178

C-18

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

DSX_CHNG_RSP_RECOVER_RETRY,DSC
recovery - DSC-RSP lost [SF Id: XXXX

System Error

Contact

[email protected]

DSX_CHNG_RSP_RETRY_EXH,DSC Err -
DSC-RSP send retries exhaustes [SF Id:
XXXX]

System Error

Contact

[email protected]

DSX_DEL_RSP_RECOVER,DSX recovery -
DSD RSP [SF Id: XXXX]

System Error

Contact

[email protected]

DSX_DEL_SUCCESS, DSD Success [SF Id:
XXXX]

System Error

Contact

[email protected]

DSX_DYN_SERVICE_LIMIT,DSX Reject -
service limit exceeded [Info:
XX:XX:XX:XX:XX:XX]

System Error

Contact

[email protected]

DSX_NO_RESOURCE,DSx Add Reject

System Error

Contact

[email protected]

DSX_PARAM_NOT_PRESENT,DSx Add
Reject

System Error

Contact

[email protected]

DSX_SF_CLS_ADD_REJECTED,DSA Err -
SF or CLS rejected [SF Id: XXXX]

System Error

Contact

[email protected]

DSX_SF_CLS_CHNG_REJECTED,DSC Err -
SF or CLS rejected [SF Id: XXXX]

System Error

Contact

[email protected]

DSX_SF_EXISTS,DSA Rejected - Service
Flow exists [SF Id: XXXX]

System Error

Contact

[email protected]

DSX_SF_NOT_FOUND,DSC-DSD Reject -
SF ID not found

System Error

Contact

[email protected]

DSX_UNK_CONF_SETTINGS,DSx Add
Reject

System Error

Contact

[email protected]

DSX_UNK_TRANSACTION_ID,DSx Action

System Error

Contact

[email protected]

DSX_VAL_PARAM_NOT_SUPP,DSx Add
Rejected

System Error

Contact

[email protected]

UL_CH_UNUSABLE, Uplink Channel
Unusable

System Error.

Contact

[email protected]

Table C-2

Additional Subscriber Event Log Messages

Summary of Contents for RedMAX AN100U



















































































































































































Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands

Redline Communications RedMAX AN100U, Administration And Maintenance Manual

Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands