Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 138 | Manualshive

Page: 138 / 178

background image

B-12

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

Restore configuration into
alternate image

The user-provided configuration file
has been applied to the alternate
(non-active) image

Information only. There is no action required.

RF-Related Messages

Air Interface is Disabled

The RF interface has been disabled by
the user.

The option to enable/disable the air/RF interface
is in the Wireless Interface menu of the
AN100U/UX’s GUI or CLI interface.

Air Interface is Enabled

The RF interface has been enabled by
the user.

The option to enable/disable the air/RF interface
is in the Wireless Interface menu of the
AN100U/UX’s GUI or CLI interface.

RF capabilities have changed.
Check RF and PHY
parameters and re-activate
the RF interface.

This message usually occurs when a
new radio is connected to an
AN100U/UX, and it is of a different
frequency range than previously
configured.

For example a 3.4-3.6GHz radio is
connected to an AN100U/UX
previously configured to use
3.6-3.8GHz)

Check RF and PHY parameters and re-activate
the RF interface. See “Checking RF and PHY
Parameters” on page 3-14.

WARNING: Unknown
Interference was Detected on
the Uplink Channel [-x dBm]

The sector controller has detected
unknown interference.

The sector controller may also report the
interference strength (-x dBm). You may need to
perform a spectrum analysis to determine the
source of the interference. See A Guide to Field
Spectral Analysis.

Also see “Interference Messages at Startup” on
page B-19 for information on how the sector
controller determines that there is interference
on the uplink channel.

WARNING: Uplink Channel
Conflict with [BS ID] [-x dBm]

A conflict with another sector
controller was detected. The BS ID
and the interference strength are
reported.

Verify proper synchronization between the sector
controllers in question, and revisit your channel
plan if problems persist.

Also see “Interference Messages at Startup” on
page B-19 for information on how the sector
controller determines that there is interference
on the uplink channel.

Table B-1

AN100U/UX Event Log Messages (continued)

Message

Description

Comment

«
...
136
137
138
139
140
...
»

Summary of Contents for RedMAX AN100U



















































































































































































Reviews:

No comments

Related manuals for RedMAX AN100U

Brand: Danfoss Pages: 14

Odyssey II Series

Brand: Dakota Digital Pages: 3

Action Replay DSi

Brand: Datel Pages: 2

Brand: Harol Pages: 16

Brand: VDO Cyclecomputing Pages: 21

Brand: Panasonic Pages: 120

Brand: Camcar Pages: 2

HookUpz Smartphone Telescope Adapter

Brand: Carson Pages: 16

Brand: Sirius Satellite Radio Pages: 8

Brand: Datasensor Pages: 2

Brand: Warmon Pages: 2

Brand: Nav TV Pages: 3

DBALL2-HYUNDAI9

Brand: Xpresskit Pages: 13

Brand: Uebler Pages: 56

Brand: IFM Pages: 17

Mesh Helmet Cover

Brand: Ops-Core Pages: 2

Brand: Kellfri Pages: 12

Flame Tracker Lite

Brand: Baker Hughes Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands