Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 74 | Manualshive

Page: 74 / 178

background image

5-12

RedMAX Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

Configuring Duplex Mode for the AN100U/UX

Use the following procedure to set the speed and duplex mode for the sector controller.

Step 1

Login to the Web client as outlined in “Connecting to the Sector Controller Web Client” on
page 2-4.

Step 2

From the Main menu select Interface Configuration > Ethernet.

The Ethernet Interface page is displayed. You can review this page to view the
configuration of the device’s Ethernet interface.

Step 3

Check the value of Management. If this parameter is set to Via Mgt port, then device
management will be done out of band via the management port. If this parameter is set to
Via Data port, then management will be done inline via the data port

Step 4

Check the value of the Mgt Port Setting parameter and set this to the required speed and
duplex mode for the sector controller management port

.

Step 5

Click Save to make your changes and return to the main menu.

SUO CLI

Step 1

Login to the CLI as outlined in “Connecting to the Subscriber Unit Command Line
Interface” on page 2-6.

Step 2

Enter the set command:

set

Step 3

Set the options for speed and duplex mode. Use the following command to enable
auto-negotiation:

set ethernet AutoNegEnabled 1

Step 4

If you do not want to use auto-negotiation, then enter the required speed and duplex mode.
See Table 5-3 for details of the available options.

set ethernet LinkSpeed 1 LinkDuplex 0

Table 5-2

Speed/Duplex Settings for the AN100U/UX Management Port

Speed

Description

Auto Detect

Auto-negotiate the speed and duplex mode with the subscriber unit.

10 Mbps Half Duplex

Operate at 10Base-T and half duplex mode only.

10 Mbps Full Duplex

Operate at 10Base-T and full duplex mode only. When using this setting
the subscriber unit must be set accordingly.

100 Mbps Half Duplex

Operate at 100Base-T and half duplex mode only.

100 Mbps Full Duplex

Operate at 100Base-T and full duplex mode only. When using this
setting the subscriber unit must be set accordingly.

«
...
72
73
74
75
76
...
»

Summary of Contents for RedMAX AN100U



















































































































































































Reviews:

No comments

Related manuals for RedMAX AN100U

Brand: Valore Pages: 4

Brand: Camtree Pages: 2

Brand: Camtree Pages: 11

Brand: Camtree Pages: 4

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Ignition Pages: 1

Brand: Oki Pages: 8

Brand: Oki Pages: 51

Brand: UniFlow Pages: 42

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: pleasant hearth Pages: 52

Brand: Roav Pages: 10

Brand: SUP’AIR Pages: 29

BELL SYSTEM FG-16 V3

Brand: M-E Pages: 2

Brand: Lennox Pages: 10

H-BLACK PRO DYNAMO

Brand: HERRMANS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands