Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 143 | Manualshive

Page: 143 / 178

background image

B-17

Appendix B AN100U/UX Event Log Messages

Redline Communications Inc. Confidential and Proprietary

Synchronization Signal not
Detected

The Slave or Backup Master has
previously been synchronized with a
Master, but has since lost the signal
and may have drifted out of phase.

The Slave will continue transmitting, however its
clock will eventually drift out of phase with the
rest of the sector if synchronization is not
restored.

A Slave, previously synchronized with
a Master, has since lost the signal.

The Slave will continue operating, however its
clock will eventually drift out of phase with the
rest of the sector, if synchronization is not
restored.

Synchronization Signal not
Detected. Waiting...

A sector controller configured as a
Slave cannot detect the
synchronization signal from the
Master or the Backup Master.

Follow the synchronization installation guidelines
for installation and troubleshooting of local or
GPS synchronization. Refer to the RedMAX
Base Station Installation Guidelines.

Synchronization with Backup
Failed

A sector controller configured as a
Master, has been rebooted, then
detected the presence of a Backup
Master, but has failed to resume
control of the Backup Master’s clock.

Follow the synchronization installation guidelines
for installation and troubleshooting of local or
GPS synchronization. Refer to the RedMAX
Base Station Installation Guidelines.

Synchronization with Backup
Ok

A sector controller configured as
Master, has been rebooted, then
detected the presence of a Backup
Master, and successfully resumed
control of the Backup Master’s clock.

Information only. There is no action required.

Synchronization with GPS is
Lost

Synchronization with a previously
detected external clock source has
been lost

Follow the synchronization installation guidelines
for installation and troubleshooting of local or
GPS synchronization. Refer to the RedMAX
Base Station Installation Guidelines.

Synchronization with GPS Ok

Synchronization with an external GPS
clock has been successfully
completed.

Information only. There is no action required.

Synchronization with Master is
Lost

A Backup Master that previously
detected the presence of a the Master
clock signal, has since lost the signal.

The Backup Master will provide a clock signal for
the rest of the Slave devices within the base
station until the signal from the Master returns.
Please follow the synchronization installation
guidelines for installation and troubleshooting of
local and GPS synchronization.

Synchronization with Master
Ok

A Backup Master has successfully
synchronized with a Master’s clock
signal.

Information only. There is no action required.

Table B-1

AN100U/UX Event Log Messages (continued)

Message

Description

Comment

«
...
141
142
143
144
145
...
»

Summary of Contents for RedMAX AN100U



















































































































































































Reviews:

No comments

Related manuals for RedMAX AN100U

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

Brand: MacDon Pages: 2

Brand: Samsung Pages: 2

Brand: D-2 Incorporated Pages: 28

Brand: D+H Pages: 12

Brand: ZARD Pages: 2

Brand: Nanoleaf Pages: 14

Brand: Waterpik Pages: 20

Water Flosser WF-06

Brand: Waterpik Pages: 2

Brand: Waterpik Pages: 6

Brand: Waterpik Pages: 24

DGIPAD-4542 - DATASHEET FOR IPAD

Brand: I.SOUND Pages: 1

Brand: OBO Bettermann Pages: 2

Brand: Hama Pages: 14

Brand: Heath Zenith Pages: 24

Brand: Beurer Pages: 24

Brand: Dreamzon Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands