Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 160 | Manualshive

Page: 160 / 178

background image

C-14

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

SF CID=XXXX Erased

The service flow [CID=XXXX] has
been deleted.

Information only. There is no action required.

SNMP reboot request

The subscriber unit is being rebooted
based on an SNMP request.

Information only. There is no action required.

Software upgrade failed

The upgrade operation failed.

Retry the upgrade.

Software upgrade successful

The upgrade operation was completed
successfully.

Information only. There is no action required.

Started CLI configuration
restore

The subscriber unit restore operation
has been initiated by a CLI request.

Information only. There is no action required.

Started CLI software upgrade

The subscriber unit software upgrade
operation has been initiated by a CLI
request.

Information only. There is no action required.

Started Provisioning software
upgrade

The subscriber unit software upgrade
operation has been initiated by TFTP
self-provisioning

Information only. There is no action required.

Started SNMP configuration
restore,

The subscriber unit restore operation
has been initiated by an SNMP
request

Information only. There is no action required.

Started SNMP software
upgrade

The subscriber unit restore operation
has been initiated by RMS.

Information only. There is no action required.

StartFrameRx failed

Debug message. Error detected in
maps.

This could be the result of poor reception, RF
issues, interference.

See “Troubleshooting Wireless Link Issues” on
page 5-18.

Subch IRng: SCh Number:nn
Frame: nn

These messages are part of the
ranging sequence, when
subchannelization has been enabled.

Normal operation. There is no action required.

Synchronization Completed

The subscriber unit has completed
scanning for a downlink channel, and
established synchronization with a
sector controller. It will now begin its
initial ranging process.

This message is part of the normal registration
process.

System startup [status]

The subscriber unit has begun the
bootup sequence. The startup status
will be included in the text of this
message. Modes specify a possible
reason for reboot. (i.e. (power cycle,
reset, CLI/SNMP request, crash, etc)

Information only. There is no action required.

TEK nn expired

This message provides information on
the status of your encryption key.

Information only. There is no action required.

When privacy is enabled, this is one of the many
steps that subscriber must perform to complete
the authentication process.

Table C-1

Subscriber Event Log Messages (continued)

Message

Description

Analysis

«
...
158
159
160
161
162
...
»

Summary of Contents for RedMAX AN100U



















































































































































































Reviews:

No comments

Related manuals for RedMAX AN100U

Brand: Happy Orange Pages: 2

Brand: KDS Pages: 72

Brand: Oki Pages: 2

Brand: Oki Pages: 20

Brand: Oki Pages: 2

Brand: Oki Pages: 2

Brand: OKIDATA Pages: 16

Brand: Parker Pages: 2

Brand: Park Tool Pages: 2

Brand: ParaZero Pages: 17

Brand: Oliver Pages: 15

Brand: Pivot Pages: 4

Video 75 Plus Studio

Brand: Sachtler Pages: 34

Brand: CAME Pages: 2

Brand: SR Suntour Pages: 10

Brand: EUFAB Pages: 12

Brand: Fisher-Price Pages: 12

Brand: Oasis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands