Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 3

Page: 3 / 178

Table of Contents

Redline Communications Inc. Confidential and Proprietary

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Other Documents in the Redline Product Suite . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Supported Redline Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

C H A P T E R

Overview

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Establishing a Spares Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Reference Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Monitoring Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Connecting to the Sector Controller Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Connecting to the Sector Controller Command Line Interface . . . . . . . . . . . . . . . 2-5

Connecting to the Subscriber Unit Command Line Interface . . . . . . . . . . . . . . . . . 2-6

Monitoring System Event Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Monitoring Statistical Results Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Monitoring the System Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Using the Ping Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10

Using the Iperf Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Network Sniffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Using the rfMonitor Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Planning/Scheduling Equipment Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

Personnel Required for Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Establishing and Recording the Baseline Configuration . . . . . . . . . . . . . . . . . . . 2-15

Maintenance Record Keeping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Establishing Secure, Remote Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

Summary of Contents for RedMAX AN100U



















































































































































































Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands

Redline Communications RedMAX AN100U, Administration And Maintenance Manual

Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands