Redline Communications RedMAX AN100U Administration And Maintenance Manual Download Page 140

Page: 140 / 178

B-14

Redline Management Suite Administration and Maintenance Guide

Redline Communications Inc. Confidential and Proprietary

MAC exception: DL EoF
Interrupt Timeout

A system reboot was caused by a
MAC exception. You may see the
following additional messages:

• UL EoF Interrupt Timeout;

• Start Scheduling Signal Timeout

Upgrade the sector controller to the latest
software version. If you are currently at the latest
software version, then contact
[email protected].

MAC exception: Start
Scheduling Signal Timeout

A system reboot was caused by a
MAC exception. You may see the
following additional messages:

• DL EoF Interrupt Timeout;

• UL EoF Interrupt Timeout;

Upgrade the sector controller to the latest
software version. If you are currently at the latest
software version, then contact
[email protected].

MAC exception: UL EoF
Interrupt Timeout

A system reboot was caused by a
MAC exception. You may see the
following additional messages:

• DL EoF Interrupt Timeout;

• Start Scheduling Signal Timeout

Upgrade the sector controller to the latest
software version. If you are currently at the latest
software version, then contact
[email protected].

RedMAX Ver. 2.1.x started

Normal startup message indicating
current software version.

Shown once at system startup.

Information only. There is no action required.

Unknown Hardware Exception A system reboot was caused by a

MAC exception. You may see the
following additional messages: DL
EoF Interrupt Timeout; UL EoF
Interrupt Timeout; Start Scheduling
Signal Timeout

This does not generate an alarm.

Sub-Channelization Messages

PHY Exception: PUSHERR !!! This message indicates the PHY

exceptions (Rx push error) when
subchannelization is enabled.

This message is specific to the AN100UX. After
one of these exceptions occurs the AN100UX
may recover itself or will need to be rebooted.

PHY Exception: RXOVF !!!

This message indicates the PHY
exception (Rx buffer overflow) when
subchannelization is enabled.

This message is specific to the AN100UX. After
one of these exceptions occurs the AN100UX
may recover itself or will need to be rebooted.

PHY Exception: RXOVLP !!!

This message indicates the PHY
exception (Rx overlap) when
subchannelization is enabled.

This message is specific to the AN100UX. After
one of these exceptions occurs the AN100UX
may recover itself or will need to be rebooted.

Table B-1

AN100U/UX Event Log Messages (continued)

Message

Description

Comment

Summary of Contents for RedMAX AN100U



















































































































































































Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands

Redline Communications RedMAX AN100U, Administration And Maintenance Manual

Search results

Summary of Contents for RedMAX AN100U

Reviews:

Related manuals for RedMAX AN100U

Brands by name

Popular brands