RAM Commercial PROMASTER 2020 Owner'S Manual Download Page 45

Page: 45 / 260

GETTING TO KNOW YOUR INSTRUMENT PANEL

Instrument Cluster Descriptions

1. Speedometer



Indicates vehicle speed.

2. Instrument Cluster Display



When the appropriate conditions exist,

this display shows instrument cluster

display messages. Refer to “Instrument

Cluster Display” in this chapter for further

information.



Odometer/Trip Odometer Display Area

US Federal regulations require that upon

transfer of vehicle ownership, the seller

certify to the purchaser the correct mileage

that the vehicle has been driven. If your

odometer needs to be repaired or serviced,

the repair technician should leave the odom

eter reading the same as it was before the

repair or service. If the technician cannot do

so, then the odometer must be set at zero,

and a sticker must be placed in the door

jamb stating what the mileage was before the

repair or service. It is a good idea for you to

make a record of the odometer reading

before the repair/service, so that you can be

sure that it is properly reset, or that the door

jamb sticker is accurate if the odometer must

be reset at zero.



Gear Selector Status (PRND)

The gear selector status “P,R,N,D,1,2,3,4,5,

6” are displayed indicating the gear selector

position. Telltales “1,2,3,4,5,6” indicate the

manual mode has been engaged and the

gear selected is displayed. Refer to “Auto

matic Transmission” in “Starting And Oper

ating” for further information on Electronic

Range Select (ERS).

3. Tachometer



This gauge measures engine revolutions

per minute (RPM x 1000). Before the

pointer reaches the red area, ease up on

the accelerator to prevent engine

damage.

4. Temperature Gauge



The temperature gauge shows engine

coolant temperature. Any reading within

the normal range indicates that the

engine cooling system is operating satis

factorily.



The pointer will likely indicate a higher

temperature when driving in hot weather

or up mountain grades. It should not be

allowed to exceed the upper limits of the

normal operating range.

WARNING!

A hot engine cooling system is dangerous.

You or others could be badly burned by steam

or boiling coolant. You may want to call an

authorized dealer for service if your vehicle

overheats. If you decide to look under the

hood yourself, refer to “Cooling System” in

“Servicing And Maintenance” and follow the

warnings under the Cooling System Pressure

Cap paragraph.

CAUTION!

Driving with a hot engine cooling system

could damage your vehicle. If the

temperature gauge reads “H,” pull over and

stop the vehicle. Idle the vehicle with the air

conditioner turned off until the pointer drops

back into the normal range. If the pointer

remains on the “H,” turn the engine off

immediately and call an authorized dealer for

service.

20_VF_OM_EN_USC_t.book Page 43

Summary of Contents for PROMASTER 2020





































































































































































































































































Search results

Summary of Contents for PROMASTER 2020

Reviews:

Related manuals for PROMASTER 2020

Brands by name

Popular brands

RAM Commercial PROMASTER 2020, Owner'S Manual

Search results

Summary of Contents for PROMASTER 2020

Reviews:

Related manuals for PROMASTER 2020

Brands by name

Popular brands