Right Indicator Button and LED
This button activates and de-activates the wheelchair’s right
indicator. Depress the button to turn the indicator on and
depress the button again to turn it off.
When activated the right indicator LED will flash in sync with
the wheelchair’s indicator(s).
External On/Off Switch Jack
This
mono jack port
allows
you
to turn the control system on
and off using a
mechanical switch
, such as a buddy button.
External Profile Switch Jack (Fig 3.2
and
3.4)
This is a stereo jack socket that allows the connection, via a
suitable adapter, of two external switches or buttons.
The function of these switches or buttons is assignable via
programing.
Please contact your authorized dealer.
The connection details for the mating stereo plug are shown
below.
If the control system is set to latched drive or actuator
operation, then the polarity of External Profile Jack 1 will be
inverted to effect a fail-safe connection for an emergency
stop button.
The Joystick Module is supplied with rubber
plugs
that must
be inserted into the Jack Sockets when no external device is
connected.
For full details of LCD Screen functions please refer to
Chapter 4.0
Fig.3.2
External Profile Jack 1
External Profile Jack 2
Common
3.2 R-Net Joystick Modules
The R-Net control system has two versions of Joystick Module
with LCD Screen, (Fig 3.3),
and
with LED buttons, (Fig 3.5).
Most of the controls are common to both, however there are
variations between the two. Each of the controls is explained
within this section.
3.3 Joystick Module LCD Screen (Fig 3.3)
On/off button
The on/off button applies power to the control system
electronics, which in turn supply power to the wheelchair’s
motors. Do not use the on/off button to stop the wheelchair
unless there is an emergency. (If you do
,
you may shorten the
life of the wheelchair drive components)
.
Horn Button
The Horn will sound while this button is depressed.
Speed Decrease Button
This button decreases the maximum speed setting.
Speed Increase Button
This button increases the maximum speed setting.
Mode Button
The Mode button allows
you
to navigate through the available
operating Modes for the control system. The available modes
are dependent on programing and the range of auxiliary output
devices connected to the control system.
Profile Button
The Profile button allows
you
to navigate through the available
Profiles for the control system. The number of available
Profiles is dependent on how the control system is
programmed.
Hazard Warning Button and LED
This button activates and de-activates the wheelchair’s hazard
lights. Depress the button to turn the hazards on and depress
the button again to turn them off.
When activated the hazard LED and the indicator LEDs will
flash in sync with the wheelchair’s indicator(s).
Lights Button and LED
This button activates and de-activates the wheelchair’s lights.
Depress the button to turn the lights on and depress the button
again to turn them off.
When activated the lights LED will illuminate.
Left Indicator Button and LED
This button activates and de-activates the wheelchair’s left
indicator. Depress the button to turn the indicator on and
depress the button again to turn it off.
When activated the left indicator LED will flash in sync with the
wheelchair’s indicator(s).
249044 Rev. A
9
R-Net Control System w/Omni2
Summary of Contents for R-net
