QNO FQR7200 User Manual Download Page 52

Page: 52 / 184

Multi-WAN Router

ISP Host:

This is the detected location for the ISP port, such as the DNS IP

address of ISP. When configuring an IP address for this function, make

sure this IP is capable of receiving feedback stably and speedily. (Please

input the DNS IP of the ISP port)

Remote Host:

This is the detected location for the remote Network Segment. This

Remote Host IP should better be capable of receiving feedback stably

and speedily. (Please input the DNS IP of the ISP port).

DNS Lookup Host:

This is the detect location for DNS. (Only a web address such as

www.hinet.net

is acceptable here. Do not input an IP address.) In

addition, do not input the same web address in this box for two different

WANs.

Note

！

In the load balance mode for Assigned Routing, the first WAN port (WAN1) will be saved for the

traffic of the IP addresses or the application service ports that are not assigned to other WANs (WAN2,

WAN3, and WAN4). Therefore, in this mode, we recommend assigning one of the connections to the

first WAN. When other WANs (WAN2, WAN3, or WAN4) are broken and connection error remove

(Remove the Connection) has been selected for the connection detection system, traffic will be shifted

to the first WAN (WAN1). In addition, if the first WAN (WAN1) is broken, the traffic will be shifted to other

WANs in turn. For example, the traffic will be shifted to WAN2 first; if WAN2 is broken too, the traffic will

be shifted to WAN3, and so on.

6.2.3 Protocol Binding

WAN Setting:

Summary of Contents for FQR7200

























































































































































































Search results

Summary of Contents for FQR7200

Reviews:

Related manuals for FQR7200

Brands by name

Popular brands

QNO FQR7200, User Manual

Search results

Summary of Contents for FQR7200

Reviews:

Related manuals for FQR7200

Brands by name

Popular brands