QNO FQR7200 User Manual Download Page 11

Page: 11 / 184

Multi-WAN Router

III. Hardware Installation

In this chapter we are going to introduce hardware interface as well as physical installation.

3.1 Router LED Signal

LED Signal Description

LED

Color

Description

Power

Green

Green LED on: Power ON

DIAG

Amber

Amber LED on: System self-test is running.
Amber LED off: System self-test is completed successfully.

LAN/WAN/DMZ: 10M-

Speed

Off

Ethernet is running at 10Mbps.

LAN/WAN/DMZ: 100M-

Speed

Amber

Ethernet is running at 100Mbps.

LAN/WAN/DMZ:

1000M- Speed

Green

Ethernet is running at 1000Mbps.

WAN/DMZ:

Green

Green LED on: WAN is connected and gets the IP address.
Green LED Blinking: Packets are transmitting through Ethernet
port.
Green LED off: WAN can not get the IP address.

LAN

Green

Green LED on: LAN is connected.
Green LED Blinking: Packets are transmitting through Ethernet
port.

USB

Green

Green LED on: USB is connected and the device is supported.
Green LED Blinking: Packets are transmitting through USB port.

Reset

Action

Description

Press Reset Button For 5 Secs

Warm Start

DIAG indicator: Amber LED flashing slowly.

Press Reset Button Over 10 Secs

Factory Default

DIAG indicator: Amber LED flashing quickly.

System Built-in Battery

A system timing battery is built into Router. The lifespan of the battery is about 1~2 years. If the battery life

Summary of Contents for FQR7200

























































































































































































Search results

Summary of Contents for FQR7200

Reviews:

Related manuals for FQR7200

Brands by name

Popular brands

QNO FQR7200, User Manual

Search results

Summary of Contents for FQR7200

Reviews:

Related manuals for FQR7200

Brands by name

Popular brands